Announcement

Collapse
No announcement yet.

how to surface wood

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • how to surface wood

    I would like to know the best way to surface wood. Such as when you goto a lumber yard and by 4/4 mahogany. I want to make pieces that are 1/4 in thick. I thought that a band saw would do the job except the saws I have seen only have about 5-6 in. space between table and the blade housing. Makes it hard to cut a 8 in wide piece so that it is 1/4 in thick and 8 in. wide. Thanks for any help.

  • #2
    Re: how to surface wood

    You need to either buy a VERY expensive saw, or buy one of the regular 14' saws and get a 'riser' for it....it doubles the depth of the cut.

    Comment


    • #3
      Re: how to surface wood

      Like Hi_Ho_Sliver is saying, get a band saw with a riser block. Your band saw is most likely set up for a riser block already. You need a planer to make the right tkickness and to get a smooth surface.

      Mike M
      SD Mike

      Comment


      • #4
        Re: how to surface wood

        shaun

        to get the right thickness you do need a planer. there is an alternative if you have a router with a straight bit. build a jig a little larger than the width of the board and afix the router to a base you can slide up and down the length of the jig. to get the thickness you want just adjust the router bit to the height you need and make as many passes as you need to get the thickness you want. for safety reasons clamp the board so it doesn't move on you and secondly make small passes until you get the thickness you need. SAFETY, SAFETY

        Comment


        • #5
          Re: how to surface wood

          Like it has been mentioned a bandsaw is the ideal tool to thin the 4/4 lumber down to close to 1/4'. This needs to be a bandsaw that is able to accept a riser block kit which will allow you to cut 12' boards. Then you can surface plane them to exact thickness needed with a planer but what I like to use because it does two steps in one is to use a drum sander. I have a 16-32 performax drum sander and can sand to fial thickness. This is the problem when buying rough sawn lumber you need various tools and machinery to achieve the dimentions you are looking for and you need the space to store these tools. But there is no more enjoyable hobby then woodworking. You get to see the results right away. Good Luck!!

          Just one other note if you own a tablesaw you can resaw up to 6' on it to the desired thickness. The disadvantage here is the kerf wastes alot of wood even if you use a thin 1/8' blade.
          John T.

          Comment


          • #6
            Re: how to surface wood

            You'd save alot of money buying the lumber in the thickness you need unless you plan on doing this alot.

            Comment


            • #7
              Re: how to surface wood

              You may be able to save money initally without buying the tools but where is the fun in that. You get a chance to play with the big boys toys. You can also build other things not just resaw wood. Like said depends on how much you want to get involved in this for this gets addictive so you have been warned. I know because I am now looking into the turning end of woodworking and the expense of new tools.
              John T.

              Comment

              Unconfigured Ad Widget

              Collapse

              Latest Topics

              Collapse

              • Linda In Phoenix
                Reply to YoraHome Laser w/CNC Engraver/Router
                by Linda In Phoenix
                New toys sometimes become tools we can use, and other times they simply are tools toward expanding our horizons and being there when an idea pops into our heads. Let us know what you try the Ortur on and how it does. I'm sincerely curious. Also....why did you choose Amazon vs the other vendors...
                Yesterday, 11:47 PM
              • will8989
                What is it?
                by will8989
                Bruce was bored and made this. What is it?...
                Yesterday, 10:57 PM
              • will8989
                Reply to First you need to make a mess
                by will8989
                It was a challenge that’s for sure. I didn’t start anything until I was all finished. It’s nice to have a clean area to work in! My biggest challenge was all those pieces of scrap wood that I just might need “someday.” They burned well in my son’s woodstove. And I did get through all the patterns....
                Yesterday, 10:54 PM
              • tgiro01
                Reply to First you need to make a mess
                by tgiro01
                Wow - Betty, what do you charge. I have things to do and I'm in the process of cleaning my shop, just to have room to do it. My problem is that I get the work bench cleared and then start working on projects again. I really need to do the workbench last.
                Yesterday, 10:05 PM
              • tgiro01
                Reply to YoraHome Laser w/CNC Engraver/Router
                by tgiro01
                I ordered and received the ORTUR Laser Master 2 from Amazon, the but haven't had a chance to even get it out of the box. Too much going
                on right now. I got the 20 watt version, which is supposed to be good for cutting, but I don't think I'll be doing much of that. There will be a learning curve...
                Yesterday, 09:57 PM
              Working...
              X