Announcement

Collapse
No announcement yet.

Marlin Key Rack

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Marlin Key Rack

    Not quite sure what I have going here but it will come to me.

    I cut the Marlin out (pattern courtesy of Dale Terrian) and didn't plan on what I wanted to do with it. I may slap it on the piece its on and some hooks for a key rack.

    I have some fine sanding to do though. Should of thought about that before hand haha

    Thoughts?

    **Edited photo per your info !** Thanks, never been a good forum poster !
    Attached Files
    Last edited by psychoCutter; 04-21-2012, 08:05 PM.

  • #2
    That turned out very nice. Key rack would be nice.

    Just a tip...

    Here is the preferred way to post photos. This method will apply a thumbnail so that messages load faster, keeping those who are still on dial up in mind.

    If it is a new thread scroll down below the message box to additional options and look for manage attachments,Click on Manage Attachments, click Browse, find your file name on your computer, click it, then click Upload. It may take a few seconds to load.
    Once you see the file name under current attachments you can close the window.
    If you want you can Preview Post (a wise choice) then if all is well, click on Submit reply.

    If you are uploading a picture to an existing thread (conversation)
    Click on the Go Advanced button under the reply box, Click on Manage Attachments, click Browse, find your file name on your computer, click it, then click Upload. It may take a few seconds to load.
    Once you see the file name under current attachments you can close the window.
    If you want you can Preview Post (a wise choice) then if all is well, click on Submit reply.
    Good luck
    "Still Montana Mike"

    "Don't worry about old age--it doesn't last that long."
    Mike's Wood-n-Things LLC

    Comment


    • #3
      Key Rack does sound good , good looking job too ........
      Usually busier than a cat in a sandbox !!!!!!!!!!! MB { Dewalt 788 only }

      Comment


      • #4
        Maybe a display for some small antique lures
        May the wind at you back .....
        Not be from Lunch.

        Don't take life too seriously; No one gets out alive.

        Beauty is in the eye of the BEERHOLDER

        Visit My Gallery

        Oily's Gallery

        http://www.picturetrail.com/oily11

        Comment

        Unconfigured Ad Widget

        Collapse

        Latest Topics

        Collapse

        • KarlB
          Reply to Cutting Styles
          by KarlB
          Sweet looking display. Excellent examples of the puzzles.

          Karl
          Today, 09:18 PM
        • Tom in Ashland
          Fiona Kingdon pattern from Summer issue
          by Tom in Ashland
          Quarter inch BB with Red Gum (Australian Eucalyptus) veneer. My first attempt at veneering and there are a couple spots where there was not quit enough glue so small pieces of the veneer came off....
          Today, 07:59 PM
        • millwab
          Cutting Styles
          by millwab
          In preparation for a scrolling demonstration I decided to make up a piece that would show the different ways I've cut puzzles. It's 2 layers of 1/8" BB. The puzzles were cut out as tray puzzles and then glued back in so pieces wouldn't get lost as it was handled.
          ...
          Today, 04:41 PM
        • jim_mex
          Reply to Workshop extension and major facelift - a work in progress - update at 13 April
          by jim_mex
          Update at 13 AprilIts been almost a month since my last post and my shop extension is progressing albeit slowly largely due to me nibbling at it on a regular basis rather than sticking with it and going full blast to get it finished.

          The outside
          of the extension is almost finished apart...
          Today, 03:45 PM
        • Rolf
          Reply to New Toy!
          by Rolf
          Quartz I only bought the air filter, That same model is sold by many distributors, I see Grizzly has it and several others. I was going to build one but this thing works great. I will get a charcoal filter for it also. Great when doing Pyrography. They also had a Pfingst brand flex shaft tool I haven't...
          Today, 07:50 AM
        Working...
        X