No announcement yet.

Layered Deer Scene

  • Filter
  • Time
  • Show
Clear All
new posts

  • Layered Deer Scene

    This was a really fun project to do, can't wait to get it in a frame made from old barn wood....

  • #2
    I cut a set in maple, walnut and bb ply.... I think I will contrast the walnut and maple ones. Not sure how I am going to finish the ply one....


    • #3

      Here are some other pics of them


      • #4
        thats a great scene, and i would love to see that first pic much bigger, the light
        on it is just perfect! nice job but those trees have to be a PITA?

        + + I Love The Smell Of Sawdust In The Morning + +


        • #5
          Very nice! I would also like to see a bigger version of your first picture. Who's pattern is that?
          RBI G4 26 Hawk, EX 16 with Pegas clamps, Nova 1624 DVR XP
          Philosophy "I don't know that I can't, therefore I can"
          Proud Member of the Long Island Woodworkers Club
          And the Long Island Scrollsaw Association


          • #6
            Very, very nice Shell, I do think they are Elk instead of Deer but that don't change a thing about the art.
            Chuck D

            When a work lifts your spirits and inspires bold and noble thoughts in you, do not look for any other standard to judge by: the work is good, the product of a master craftsman.
            Jean De La Bruyere...

            Hegner 18, Delta p-20, Griz 14 inch Band saw


            • #7
              Issue 40 page 20 pattern by Terry Foltz


              • #8
                photobucket pics

                How do I post a bigger pic? Here are links to photobucket maybe that will help... I took them with my cell phone....


                Unconfigured Ad Widget


                Latest Topics


                • handibunny
                  Reply to EX dust collection holes screwed up a project.!
                  by handibunny
                  Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
                  Today, 09:21 AM
                • Bill Wilson
                  Reply to EX dust collection holes screwed up a project.!
                  by Bill Wilson
                  I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
                  Today, 09:06 AM
                • cwmagee
                  Reply to EX dust collection holes screwed up a project.!
                  by cwmagee
                  Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
                  Today, 08:40 AM
                • Rolf
                  Reply to EX dust collection holes screwed up a project.!
                  by Rolf
                  That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
                  Today, 07:28 AM
                • handibunny
                  Reply to EX dust collection holes screwed up a project.!
                  by handibunny
                  Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
                  Today, 06:21 AM