There are no conversations in this channel.
Please log in to your account to view your subscribed posts.
| Topics | Statistics | Last Post | ||
|---|---|---|---|---|
|
39 responses
2,833 views
0 likes
|
by SteveK
08-22-2013, 10:03 PM
|
|||
|
8 responses
180 views
3 likes
|
by Pop
09-04-2020, 08:21 PM
|
|||
|
7 responses
110 views
0 likes
|
by Bill Wilson
08-11-2020, 02:51 PM
|
|||
|
8 responses
129 views
0 likes
|
by jim_mex
08-10-2020, 09:21 AM
|
|||
|
16 responses
248 views
0 likes
|
by will8989
07-19-2020, 07:01 PM
|
|||
|
14 responses
160 views
4 likes
|
07-17-2020, 08:05 AM
|
|||
|
12 responses
175 views
1 like
|
by Plaquerd
07-15-2020, 10:58 AM
|
|||
|
3 responses
75 views
2 likes
|
by Sandy Oaks
07-13-2020, 04:27 PM
|
|||
|
9 responses
105 views
1 like
|
07-07-2020, 01:45 PM
|
|||
|
12 responses
90 views
4 likes
|
by NC Scroller
07-06-2020, 06:28 AM
|
|||
|
3 responses
61 views
1 like
|
by Jim McDonald
06-21-2020, 06:26 PM
|
No topics found.
-
Mounted the gears on the furnace door today and started the right side latch assembly. Only got about 2hours in before hands and hips gave out. It doesn't look too bad.. Just a little lost in the middle of the door. Latch works fine. I made it so the latch can be raised without using the gear process...09-04-2020, 08:21 PM
-
Hi Pop - Your project definitely goes past my attention span limit of anything I might wish to tackle but this doesnt take away anything from it.
A really neat idea, great scrolling work and I can't wait to see the end result mounted....09-01-2020, 04:52 PM -
POP, What a fun project.
I have that program, I wish it allowed you to design an entire gear train instead of just two at a time.08-30-2020, 08:29 AM -
This was really cool. You must enjoy mechanically based things.08-29-2020, 07:34 PM -
NC .. It's not patience. I believe it started out as boredom lately. LOL I actually started scrolling back in the mid 70's. I'd scroll.. break a lot of blades and quit. Even sold the saw. Bought another saw sometime in the early 80's. Used it for a while and broke a LOT of blades Gave it to a buddy....08-29-2020, 06:08 PM
-
Pop I really envy you. I don't think I have the patience to do something like that just for looks.08-29-2020, 04:35 PM
-
A free program I've had for quite q while called 'Gear generator'. It does 1 or 2 gears at a time, pin gears, rack gears, chains, sprockets, etc. A very nice design program.
The rest is done on my Ryobi 16" scroll saw.08-29-2020, 10:17 AM -
That is very interesting! How did you design and cut the gears?08-29-2020, 06:11 AM
-
Been working with a lot of teeth this week and I'm not even a dentist. I think it's up over 200 now. And I'm still sane! I think. Going to be attached to one of the barn doors I just made for the basement "wrecked room". Not really going to lock anything but it will be functional. Think bank...08-28-2020, 08:03 PM
-
Reply to I would like your helpThat's a nice project. Looking forward to seeing yours when done.
As for grain direction, does the pattern offer any guidance? Sometimes there are indicator lines on the pattern for each piece, showing the recommended grain direction. If not, then it's up to your best judgement. There...08-11-2020, 02:51 PM