Announcement

Collapse
No announcement yet.

Amazing gears - Kinetic gear toy

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Amazing gears - Kinetic gear toy

    Birch plywod, 4mm
    watch the video to see how it works and how it was made:
    Alex Fox Patterns
    http://alexscrollsaw.wixsite.com/scrollsawpatterns

  • #2
    I love it!

    Comment


    • #3
      Awesome looking project Alex! I look forward to cutting it!

      Karl
      Karl in Sunny Southwest Florida

      Comment


      • #4
        What glue do you use?
        Rolf
        RBI G4 Hawk, Delta SS350, Nova 1624 DVR XP
        Philosophy "I don't know that I can't, therefore I can"
        Proud Member of the Long Island Woodworkers Club
        And the Long Island Scrollsaw Association

        Comment


        • #5
          Originally posted by Rolf View Post
          What glue do you use?
          I useed glue "88" of Ukrainian production, instruction: apply glue on both surfaces, wait about 10-15 minutes until the glue dries, squeeze the glued surfaces. In the USA similar glue calls "Contact Cement"
          Alex Fox Patterns
          http://alexscrollsaw.wixsite.com/scrollsawpatterns

          Comment


          • #6
            Thank you Alex.
            Rolf
            RBI G4 Hawk, Delta SS350, Nova 1624 DVR XP
            Philosophy "I don't know that I can't, therefore I can"
            Proud Member of the Long Island Woodworkers Club
            And the Long Island Scrollsaw Association

            Comment


            • #7
              Got my patterns yesterday. Hope to work on it this evening.
              AKA Paul from Washington State

              Comment


              • #8
                This is really cool - thanks for sharing
                Jim in Mexico

                Logic will get you from A to B. Imagination will take you everywhere.
                - Albert Einstein

                Comment


                • #9
                  Very nice. I love it.
                  -Bill

                  My saw is a DeWalt788 Measure twice; cut once; count fingers after cut

                  Comment


                  • #10
                    I made one of these and it was a lot of fun, but I could not get it glued to where it would work and still hold together. After a few cycles it would fall apart somewhere. I have vowed to try again one of these days, and use a little bigger dowels and different glue. I love building things with gears and movement. Always fun, even if I fail. The three "Robots" I built were the most fun of any I did, they worked for me. http://www.lisaboyer.com/Claytonsite...laboratory.htm. I am determined Alex's geared toy well also.
                    AKA Paul from Washington State

                    Comment

                    Unconfigured Ad Widget

                    Collapse

                    Latest Topics

                    Collapse

                    • alexscrollsaw
                      Tiger fretwork
                      alexscrollsaw
                      Tiger fretwork, 450 cuts
                      Size 10x13 inches (without frame), birch plywood, 1/6 inch, gloss varnish
                      pattern is available at https://www.etsy.com/shop/AlexFoxUA

                      ...
                      Today, 04:03 AM
                    • will8989
                      Conversation with Bruce
                      will8989
                      Me: I can’t believe I’m almost out of wood. Only 2small pieces of cherry and some poplar. No wood, no baskets for Wednesday night. Bruce: well, where is the wood? Me: in the bank. Bruce: what’s it doing in the bank? Me: seriously? He went to the carpenter shop where the sawmill is for Elm and...
                      Today, 12:56 AM
                    • will8989
                      Reply to Farmers Mkt today
                      will8989
                      Another great day yesterday, almost a sell out!!! Sold all but 3 Small baskets, some card holders and a few other things. Repeat customers. Freezing cold!!! Now, what do I take for Wednesday night?
                      Today, 12:40 AM
                    • hotshot
                      Reply to Coin Cutting Weekend
                      hotshot
                      Sorry, I totally missed this question, for CorelDraw, crop you pattern to the edges on all sides, then scale the pattern to 100mm x 100mm then export that to PDF. What that does is than anyone can take you pattern then make it fit any coin by just printing to a percentage that matches the size of the...
                      Yesterday, 11:44 PM
                    • Quartz43
                      Reply to epoxy
                      Quartz43
                      I have used several different epoxy. I use 5 and 15 minute epoxy for most things. I use the Bob Smith brand from Amazon. I mix it in small pill cups and measure by weight with a cheap small digital scale. One does need to be careful as it is not mixed one to one by weight and you have to check directions....
                      Yesterday, 06:51 PM
                    Working...
                    X