Announcement

Collapse
No announcement yet.

HVLP guns

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • HVLP guns

    I have never been good with a rattle can at spraying anything I build, and I thought of the HVLP guns sold on line at Harbor Freight. I wondered what guns you all used and are any of the guns sold at HF any good, Not sure if I will like this or not, so I don't wish to spend allot of money on one right now
    Hawaiilad
    Larry

  • #2
    I have an Earlex 3500 HVLP that is great for items larger than a 1' cube. Easy to use and clean up. It isn't very good at smaller things like 6" - 8" boxes where you want to spray the inside or not over-spray details. Greatest thing is that the system is completely self contained and you don't need a compressor. You are suppose to spray from 12" away and the finish surface dries very quickly.

    I bought one of the HF HVLP guns and have had mixed results. Some of it could just be my own talent level. You will need a compressor, inline filter and a regulator in addition to the gun. I use a pancake compressor and it can work for smaller items before you need to wait for the pressure to come back up. Overspray was a bigger problem with this gun than the Earlex with a bigger spray pattern.

    Another option for smaller items can be an air brush. I went through several brands before figuring they all had quirks. Biggest thing is to make sure the airbrush has the right size needles for the finish you want. All of them can spray "air brush" paint and liquids thinned to consistency of milk. If you want to spray many of the water based finishes or latex paints you need to change the needle assemblies and some of the guns don't allow that or have the larger sizes. Go to a hobby or art store for more advise on these.

    Steve.
    Steve.
    EX-16, DW-788, Dremel 1680

    Comment


    • #3
      I have a couple gravity feed, HVLP guns. One is from Grizzly and is a small detail gun. Works great for smaller projects. The other one is a full size gun that I bought at Home Depot. I've only ever used either of these to spray shellac and they work well for that, but I can't vouch for their ability to spray other materials. Much has to do with the tip size. I think the full size gun has a 1.2mm or 1.4mm tip and the detail gun is a .8mm tip. Neither of these guns were very expensive. I run them off of my 5hp, 25 gallon compressor.
      Homer : "Oh, and how is education supposed to make me feel smarter. Besides, every time I learn something new, it pushes some old stuff out of my brain."

      Comment


      • #4
        I have the Earlex HV5500. Clean up is easy, it is a self contained system and does a nice job.
        When I first got it I was spraying latex paint with it and going by the instructions I had to thin the paint way down almost scary how much it needed to be thinned. I could not believe how well everything covered with the paint that thin. It will definitely make your paint go farther.
        I have also run shellac through it, all I can say is make sure you wear a respirator because I didn't and it took a few days for me to be "right" again. The shellac also needed thinning so it was like breathing a denatured alcohol mist while spraying.
        Tim

        In God we trust, all others must pay cash!

        I don't want no bargains, they always cost me more money.

        Comment

        Unconfigured Ad Widget

        Collapse

        Latest Topics

        Collapse

        • old fa_t
          And now for the questions
          by old fa_t
          I saw a "practice pattern" to learn how to operate my saw. I decided to print out what I thought was a fairly simple pattern that would cover all the cuts and possibly have something at the end. Please tell me that the pattern lines are really just suggestions. Improvisation is acceptable....
          Today, 12:49 PM
        • Sandy Oaks
          ArtCrafters - Pegas Scroll Saw Blades
          by Sandy Oaks
          For obvious reasons, I can't put this on the website. Repackaged and labeled from gross packs. Order any quantity and mix styles and sizes. Shipping $3.50 US only. Order from Denny by email at [email protected] to receive the following prices:

          Pegas MGT Blades $2.92
          ...
          You do not have permission to view this gallery.
          This gallery has 1 photos.
          Today, 09:58 AM
        • Rolf
          Reply to This is what was in the Mayo Boxes
          by Rolf
          Isn't that called Moonshine?...
          Today, 08:09 AM
        • markdavd
          Reply to This is what was in the Mayo Boxes
          by markdavd
          Those are great! I would be interested in seeing how you box them.

          BTW, Everclear is banned in some states but still available in others. I also recently saw another brand of 190 proof at the local ABC store here in Gibsonville, NC. (I did a quick Google and found the brand is Diesel)
          Today, 05:56 AM
        • NC Scroller
          Reply to This is what was in the Mayo Boxes
          by NC Scroller
          Totally agree for one project. I think that this is where my ADHD brain helps. I usually end up with numerous project waiting finish. When the weather is right I take them outside and spray. The water based poly is nice because cleanup is little more than running warm water through the spray un...
          Yesterday, 10:23 AM
        Working...
        X