Announcement

Collapse
No announcement yet.

Backing and other supplies

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Backing and other supplies

    For the good folks that shop at AC Moore and Micheal's I have found a better resource. It is a chain of art supply stores. I listed the locations below. They are a lot cheaper and have a much much much larger color selection then the typical "craft stores".

    P.S. I have not connection to this business. Just a happy customer.

    They do mail order as well:
    Art Supplies and Materials at Jerry's Artarama

    AUSTIN, TX

    Jerry's Artarama
    6010 N IH 35
    Exit 238A
    Austin, TX 78752

    (512) 420-9359
    [email protected]


    DEERFIELD BEACH, FL

    Jerry's Artarama
    242 South Federal Hwy
    Hillsboro Square
    Deerfield Beach, FL 33441

    (954) 427-6264
    [email protected]


    FORT COLLINS, CO

    Jerry's Artarama
    420 South College Ave
    Fort Collins, CO 80524
    Discount Art Supplies @ Retail Convenience

    (970) 472-8505
    [email protected]

    HOUSTON, TX

    Jerry's Artarama
    12974-A Willowchase Dr
    Houston, TX 77070

    (832) 237-6070
    [email protected]


    KNOXVILLE, TN

    Jerry's Artarama
    5220 Homberg Dr
    Knoxville, TN 37919

    (865) 588-0738
    [email protected]


    MIAMI, FL

    Trail Plaza
    1140 SW 67th Ave
    Miami, FL 33144

    (305) 262-0475
    [email protected]

    Nashville Art Supply Store

    Jerry's Artarama
    5361 Mount View Road
    Antioch, TN 37013

    (615) 731-5901
    [email protected]


    NORWALK, CT

    Jerry's Artarama
    360 Main Ave
    Norwalk, CT 06851

    (203) 846-2279
    [email protected]


    PROVIDENCE, RI

    Jerry's Artarama
    14 Imperial Place
    Providence, RI 02903

    (401) 331-4530
    [email protected]

    RALEIGH, NC

    Jerry's Artarama
    3060 Wake Forest Road
    Raleigh, NC 27609

    (919) 876-6610
    [email protected]


    TEMPE, AZ (PHOENIX)

    Jerry's Artarama
    Fairlanes Village, Suite 1-3
    4421 South Rural Road
    (Intersection of HWY 60)
    Tempe, AZ 85282

    (480) 775-6787
    [email protected]


    VIRGINIA BEACH, VA

    Jerry's Artarama
    5258-A Corner of Providence
    and Kempsville Road
    Fairfield Shopping Center
    Virginia Beach, VA 23464

    (757) 495-7380
    [email protected]

    WEST HARTFORD, CT

    Jerry's Artarama
    1109 New Britian Ave
    West Hartford, CT 06110

    (860) 232-0073
    [email protected]


    WEST ORANGE, NJ

    Jerry's Artist Outlet
    Essex Green Plaza
    Route 280 & Prospect Ave
    West Orange, NJ 07052

    (973) 669-0995
    [email protected]


    WEST PALM BEACH, FL

    Jerry's Artarama
    2601-12 South Military Trail
    The Shoppes at Cresthaven
    West Palm Beach, FL 33415

    (561) 434-2288
    [email protected]
    Scott
    Creator of fine designer sawdust.

  • #2
    Nice information to have.
    Last edited by wood-n-things; 09-16-2011, 11:31 AM.
    "Still Montana Mike"

    "Don't worry about old age--it doesn't last that long."
    Mike's Wood-n-Things LLC

    Comment


    • #3
      Thanks for the links.
      Tony

      Comment

      Unconfigured Ad Widget

      Collapse

      Latest Topics

      Collapse

      • MidMich324
        Reply to hegner 2"
        by MidMich324
        Just Wondering...

        Is the table size on the 22" hegner saw as on the 18" hegner saw?

        With the 22" inch one you get 4 more inches of depth of cut but do you also get a few more inches of table?
        Yesterday, 09:30 PM
      • will8989
        Reply to Spring Issue
        by will8989
        I had to fool around with copying and taping a pattern again today. This wasn’t as bad as the fish, but still a pain. I use rapid resizer. Scan a pattern, put in size I want and it prints it out. If more than one page, it numbers each page at the top and I tape them together. Had the fish pattern...
        Yesterday, 09:28 PM
      • millwab
        Reply to Peanuts #1
        by millwab
        Rolf, I cover it with clear contact paper (comes off clean without leaving a residue) and draw a grid for the direction I want to cut (ie horizontal or diagonal) to keep the rows even. The rest is all freehand....
        Yesterday, 02:51 PM
      • Don in Brooklin On
        Reply to Spring Issue
        by Don in Brooklin On
        Rolf

        I use acrobat reader. The poster feature will enlarge and if it goes to multiple pages it will put in cut marks. Even if the page is over letter size it will spread to multiple pages at 100%.

        If it is in PDF form you can open with Inkscape or GIMP and select what you...
        Yesterday, 01:48 PM
      • theframer
        Reply to YoraHome Laser w/CNC Engraver/Router
        by theframer
        Hi Linda, great find...I think.

        Please keep us up to date with any information you receive. I would really like to get into this, but my computer skills are almost nonexistent, I need something that a 74 year old air head 🙄 can figure out. Thanks for sharing.

        Rick
        Yesterday, 12:05 PM
      Working...
      X