Announcement

Collapse
No announcement yet.

Ex 30

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Ex 30

    No matter how tight or what size blade I use the bottom blade holder keeps releasing the blade in the middle of a cut.

    I have resquared the holders and even tried roughing them but the blade still keeps coming loose from the bottom holder.

    Any suggestions would be greatly appreciated.

    I moved your thread to a more appropriate forum to maximize traffic and get you more responses to your request/question.
    Last edited by wood-n-things; 08-30-2011, 08:57 AM.

  • #2
    I'd suggest calling ray at Seyco. You are wiping down the blades themselves with mineral spirits right?
    "Still Montana Mike"

    "Don't worry about old age--it doesn't last that long."
    Mike's Wood-n-Things LLC

    Comment


    • #3
      Originally posted by wsmith0896 View Post
      No matter how tight or what size blade I use the bottom blade holder keeps releasing the blade in the middle of a cut.

      I have resquared the holders and even tried roughing them but the blade still keeps coming loose from the bottom holder.

      Any suggestions would be greatly appreciated.

      I moved your thread to a more appropriate forum to maximize traffic and get you more responses to your request/question.
      I had the same problem with my EX30 and made a small wooden knob with a cut out in the center to go over the existing knob so I could get a little more torque on it to tighten. I also had to adjust the allen screw depth on the opposite side of the knob. I have not had any trouble since. Steve
      If This HillBilly Can't Fix it Then it Ain't Broke!!!
      My Gallery
      [email protected]

      Comment


      • #4
        I did have the sme trouble ,until I figured out that I was puting the blade to far up in the top holder.

        I hope this helps you out.

        Comment

        Unconfigured Ad Widget

        Collapse

        Latest Topics

        Collapse

        • cwmagee
          Pegas Large Scrollsaw Table
          by cwmagee
          A couple of months ago I ordered the Large Pegas Scroll Saw Table for my EX21 from Denny which I received about a week later. I installed it immediately and made a few test cuts. Since then I have been busy with several Urban renewal projects around house as well putting the yard to bed for the winter....
          Yesterday, 07:28 PM
        • Rolf
          Reply to I admit it... I splurged on a new "toy"
          by Rolf
          Back in the late 90's I bought a Incra 2000 Miter gauge. Incredibly precise. The problem was that it only adjusted in one direction, It rarely gets used. It locks in to half degrees. More recently I bought a Kreg fence which has a pin that precisely locates the frequently used angles.
          That is...
          Yesterday, 08:15 AM
        • Jimern
          Reply to Farmers market "survey"
          by Jimern
          The crafters market here in Kerrville, TX is $25 per 10x10 spot per event. We sell 8 months out of the year, Jun/Jul is too hot, and Jan/Feb is too cold. No insurance requirement but we do have to show a sales tax permit and collect sales tax.

          Personally I would never sell in a venue that...
          Yesterday, 06:29 AM
        • will8989
          Reply to Farmers market "survey"
          by will8989
          The one I do is under a pavilion on County Property, about 60 spaces. They run 4 “seasons”, spring 6 weeks, summer May - mid September, fall sept to Mid November, and holiday fare Mid November until end of year. Cost is $75 per season, per day as they are open Saturday and Sunday. If you are called...
          10-20-2020, 11:10 PM
        • will8989
          Reply to Farmers market
          by will8989
          Ours are run by the state Ag Dept. They have very strict rules as to masks and distancing. The Ag Dept does come and visit to make sure rules are being followed. We stand behind the table and use the tailgate for packaging. I have people place their credit card in the reader on my phone and remove...
          10-20-2020, 10:31 PM
        Working...
        X