Announcement

Collapse
No announcement yet.

Need old Craftsman saw Manual help.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Need old Craftsman saw Manual help.

    Hi all,

    I was just at my brother inlaws house and he showed me a scroll saw that my father had given him many years ago. It is an old Craftsman Model 103.23150 (Craftsman/King-Seeley 18" scotch-yoke design jig saw)
    If anyone has the manual for this old beast I would love a copy of it.
    I can rebuild the blade clamps ( just flat set screws with metal shims)
    But it would be interesting to have the manual.

    Thank goodness that the saw technology has progress beyond those type of saw.
    Rolf
    RBI G4 26 Hawk, EX 16 with Pegas clamps, Nova 1624 DVR XP
    Philosophy "I don't know that I can't, therefore I can"
    Proud Member of the Long Island Woodworkers Club
    And the Long Island Scrollsaw Association

  • #2
    Rolf, I obtained a manual for an old Craftsman table saw, 1960 era from: [email protected]. I just sent them an e-mail and they sent me a copy of the owner's manual free of charge. You might try sears.com also.
    Good luck with it. Mick P-20
    Mick, - Delta P-20

    A smile is a small curve that straightens everything out.

    Comment


    • #3
      craftsman model 103.23150 scroll saw

      rolf did you find a manual? If so, how can I get a copy? thanks

      Comment


      • #4
        I need a manual for the Craftsman Scroll Saw nodel 137286220.
        Please help

        Comment


        • #5
          Rolf,
          http://www.searspartsdirect.com/part...&searchCount=1
          Is Sears site but most parts are nla from Sears even common hardware.
          Manuel,
          http://www.searspartsdirect.com/part...&searchCount=1
          is for yours
          Last edited by je_west; 07-23-2010, 09:10 PM.
          John

          Comment

          Unconfigured Ad Widget

          Collapse

          Latest Topics

          Collapse

          • Bill Wilson
            Reply to Tough Decisions
            by Bill Wilson
            Well, unfortunately, I have also decided to let my subscription lapse. I've been debating it for the past couple years. It isn't so much the money, but it's more the disappointment when yet another issue has so little in it that really appeals to me. The final straw was this past Fall/Winter edition...
            Today, 09:51 AM
          • planeur
            Reply to My covid angel
            by planeur
            Thanks to all !😀 Your comment are very good and make sense!

            My piece is 8"X8" X 1/2" thick.
            I though when I cutted the piece to do it in 1 piece or 4/5 , but after a while I decided to do it in one piece and carved it to have a 3D aspect.
            Was it a good idea.....?...
            Today, 09:45 AM
          • Rolf
            Reply to My covid angel
            by Rolf
            Great designe! I would have gone a bit further than Linda, Scott and Gladefade I would cut it into more pieces to make shaping easier. Taper the clouds from right to left, taper the wings so that they are lower where they attach to the body. Taper the neck so that it looks like it is going into the...
            Today, 09:02 AM
          • Rolf
            Reply to Tough Decisions
            by Rolf
            The never ending dilemma. I only get two magazines SSWWC and Wood carving Illustrated. Even if I don't make something in every issue there is usually something in each one that I have never tried and that will either challenge or inspire me. Yes I know that I do test cutting for them and they have occasionally...
            Today, 08:49 AM
          • NC Scroller
            Reply to My covid angel
            by NC Scroller
            I would start by tracing your piece on a piece of 1/8" (3mm) material and then cut the back our such that it is a fraction smaller that your project. Then I would cut your piece into two pieces. I mean cut the angel from the cloud. I would then put the cloud on the 1.8" backer and then with...
            Today, 07:27 AM
          Working...
          X