Announcement

Collapse
No announcement yet.

delta p-20

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • delta p-20

    i have just ordered a p-20 it is on the way in about a week any good thoughts or bad thoughts i would love your opinion thanks jack

  • #2
    Congradulations on your new saw Jack.
    I have had mine a couple of months and I love it.
    Looking foreward to seeing some nice projects ,keep us updated.
    Bill
    Delta P-20

    Comment


    • #3
      yyyyyyyyyyyyyyaa. your new saw is on the way. I have to omet. I don't know that saw. but. I am sure you will have a great jernny learning all kinds of stuff. good luck. and I too am excited for you. I sure know how I felt when I got my first saw. after waiting 10 years. they are all good. some are better thats all. just like bread. they will all fill the whole . but some just taste better. Have fun. your friend Evie

      Comment


      • #4
        thoughts and opinions requested huh? Ok, I suggest you kiss your wife now, before the saw arrives, as you wont have much time for her once the saw shows up. Butter her up good now, so she might throw you some food down by the saw so you dont have to get up from your projects! Enjoy the saw, your going to love it! Dale
        Dale w/ yella saws

        Comment


        • #5
          Wow Jack,

          A P-20, you are going to love it according to what I have read on them.

          But just wait, Bill Young will surely comment on your purchase: he has one and I don't think it could be parted from his dead fingers when the time comes

          Never having owned one myself, I can only say that it's classified with the "good" purchases, so you definitely will not regret it.

          Remember to keep the first projects you do on it, and show us the results (don't be shy).

          Regards,
          Marcel
          http://marleb.com
          DW788. -Have fun in the shop or it isn't a hobby anymore.

          NOTE: No trees were killed in the sending of this message, but a large number of electrons were terribly inconvenienced.

          Comment


          • #6
            Jack, I have had my P-20 for over 2 years now and love it. I had a 20" VS Delta before and had to use a tool to change the blade and I could not top feed with it. When I purchased mine Delta was having a problem with the rod in the back of the saw that lets the upper arm raise and lower, I had to return the first one and they shipped me another which has had no problems. I believe Bill Young notified Delta of this problem and they checked all of their unsold saws and corrected the problem. I had no problem going from a VS to the 6 speed belt drive because I very seldom change the speed, it only takes a few seconds to change the belt. Have fun with your new toy. Mick.
            Mick, - Delta P-20

            A smile is a small curve that straightens everything out.

            Comment


            • #7
              The lack of decent air from the blower on the low speeds is the only fault I can find of the saw.
              Brett

              Only Robinson Crusoe could get everything done by Friday!!

              Comment

              Unconfigured Ad Widget

              Collapse

              Latest Topics

              Collapse

              • Quartz43
                Reply to Work in Progress. What is with FOX publishing?
                by Quartz43
                Maybe nothing has changed ? But is there anything that can be done to make it easier. The very large projects are difficult to copy over several pages and put together properly. I believe in making improvements and not preserving the status quo.

                I enjoy the challenge of cutting a project...
                Today, 08:48 PM
              • keystonecop
                Reply to Work in Progress. What is with FOX publishing?
                by keystonecop
                This is not a problem with the magazine for my issue.. It is a problem with the book having resized the drawings without giving the actual size.

                I do again apologize for my post.. I cannot use the right words to explain it.. so maybe someone should just remove the post....
                Today, 07:29 PM
              • markdavd
                Reply to Work in Progress. What is with FOX publishing?
                by markdavd
                Reading these replies, I am still trying to figure out what the problem really is. I haven't noticed changes in how they publish recently and I don't think I ever had trouble making copies of of the patterns I want to cut.

                How did you copy the patterns 10 years ago? What has changed?...
                Today, 06:43 PM
              • Quartz43
                Reply to Work in Progress. What is with FOX publishing?
                by Quartz43
                I am very glad to hear this and that Fox will look into the issue. Hopefully, they can do some things to try to make it easier to copy patterns.
                Today, 06:34 PM
              • keystonecop
                Reply to Work in Progress. What is with FOX publishing?
                by keystonecop
                First I didn't mean to stir up a hornet's nest. Sorry for that. I will share that Kaylee Schofield reached out to me after my post (not sure if this forum or Facebook. From my past experience with her, she cares. I do believe she will address this issue. I do not think she is the type of person...
                Today, 05:36 PM
              Working...
              X