Announcement

Collapse
No announcement yet.

Peanuts #1

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Peanuts #1

    Time to start cutting up the 2020 calendar.
    This one is 12"x11.25", 240 pieces
    01 Snoopy and bunnies puzzle front.jpg 01 Snoopy and bunnies puzzle back.jpg
    Bruce
    . . . because each piece will be someone's heirloom someday.
    visit sometime
    Hawk 220VS, Delta 40-570

  • #2
    Very impressive.
    Scott
    Creator of fine designer sawdust.

    Comment


    • #3
      Is this a freehand cut? Or do you have a pattern that you overlay?
      Rolf
      RBI G4 26 Hawk, EX 16 with Pegas clamps, Nova 1624 DVR XP
      Philosophy "I don't know that I can't, therefore I can"
      Proud Member of the Long Island Woodworkers Club
      And the Long Island Scrollsaw Association

      Comment


      • #4
        I agree with Scott, very impressive.
        Denny
        ArtCrafters in Dayton, TN

        Comment


        • #5
          I love Snoopy!
          Linda at www.ArtIngrained.com

          Comment


          • #6
            Great job, SNOOPY rules.

            There are very few people who had the insight about life that Charles Schultz had.

            Thanks for sharing

            Rick
            Rick
            Just because the circus left town, doesn't mean the Monkey's off your back

            Comment


            • #7
              Originally posted by Rolf View Post
              Is this a freehand cut? Or do you have a pattern that you overlay?
              Rolf, I cover it with clear contact paper (comes off clean without leaving a residue) and draw a grid for the direction I want to cut (ie horizontal or diagonal) to keep the rows even. The rest is all freehand.
              Bruce
              . . . because each piece will be someone's heirloom someday.
              visit sometime
              Hawk 220VS, Delta 40-570

              Comment


              • #8
                Thanks Bruce, great tip and one more question what blade did you use?
                Rolf
                RBI G4 26 Hawk, EX 16 with Pegas clamps, Nova 1624 DVR XP
                Philosophy "I don't know that I can't, therefore I can"
                Proud Member of the Long Island Woodworkers Club
                And the Long Island Scrollsaw Association

                Comment


                • #9
                  Originally posted by Rolf View Post
                  ... what blade did you use?
                  I still have some puzzle blades from Ben Fink. Once I run out of them I’ll have to ask Denny what he recommends for a substitute.
                  Bruce
                  . . . because each piece will be someone's heirloom someday.
                  visit sometime
                  Hawk 220VS, Delta 40-570

                  Comment


                  • #10
                    They may be the FD puzzle blades. I have also used the Pegas 2/0 28 TPI blade. It has NO reverse teeth.
                    Rolf
                    RBI G4 26 Hawk, EX 16 with Pegas clamps, Nova 1624 DVR XP
                    Philosophy "I don't know that I can't, therefore I can"
                    Proud Member of the Long Island Woodworkers Club
                    And the Long Island Scrollsaw Association

                    Comment


                    • #11
                      Originally posted by Rolf View Post
                      They may be the FD puzzle blades. I have also used the Pegas 2/0 28 TPI blade. It has NO reverse teeth.
                      IDK? I remember that Ben sold Pegas blades, but the label on this package just says "Ben's Blades, Ultra Thin Puzzle Blade". When Denny started selling Pegas blades I asked him and he told me Pegas doesn't sell a specific "puzzle" blade. The 2/0 might be their answer.
                      Bruce
                      . . . because each piece will be someone's heirloom someday.
                      visit sometime
                      Hawk 220VS, Delta 40-570

                      Comment


                      • #12

                        Bruce I just looked up the Pegas blade and the Flying Dutchman puzzle blade.
                        Pegas TPI 28.2 Thickness .087" Width .0236"
                        FD TPI 31 Thickness .08 Width.023

                        So the Flying Dutchman is a bit thinner , not sure it would make a significant difference. Three teeth per inch may cut a bit faster. The FD blade is thinner by a couple of sheets of paper.

                        Hope that helps.
                        Last edited by Rolf; 01-22-2021, 09:28 AM.
                        Rolf
                        RBI G4 26 Hawk, EX 16 with Pegas clamps, Nova 1624 DVR XP
                        Philosophy "I don't know that I can't, therefore I can"
                        Proud Member of the Long Island Woodworkers Club
                        And the Long Island Scrollsaw Association

                        Comment


                        • #13
                          Originally posted by Rolf View Post
                          Bruce I just looked up the Pegas blade and the Flying Dutchman puzzle blade.
                          Pegas TPI 28.2 Thickness .087" Width .0236"
                          FD TPI 31 Thickness .08 Width.023
                          Hope that helps.
                          Thanx Rolf. I also found a package of Olson 3/0 blades I had. They are 33TPI x .008T x .022W
                          I’m guessing that’s their equivalent of a puzzle blade since they don’t sell one specifically labeled as such.
                          Bruce
                          . . . because each piece will be someone's heirloom someday.
                          visit sometime
                          Hawk 220VS, Delta 40-570

                          Comment

                          Unconfigured Ad Widget

                          Collapse

                          Latest Topics

                          Collapse

                          Working...
                          X