Announcement

Collapse
No announcement yet.

new here

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • new here

    Hi everyone
    i'm new to this site but not to scroll sawing . Have been sawing for the last 21 years.me and my wife us'ed to set up at craft shows till she pasted awaynow i want to start back in it again

  • #2
    Welcome Pete,
    This is a busy blog, with tons of great stuff, good advise, and I'm sure you will make some great friends.

    Comment


    • #3
      welcome......good bunch of people here......lots of experience....and they love to share.....post some pics of your stuff...

      bob
      "The Journey is the Reward"

      Comment


      • #4
        Welcome A Board!! You will be hard pressed to find a friendlier or more knowledgeable group on the net re: woodworking. Share your knowledge and do not hesitate to ask questions. The only dumb question is the one that remains unasked.

        You may find the stickies at the top of this forum to be very helpful. Use the Link below.

        Message Board FAQ, Suggestions and Feedback - Scroll Saw Woodworking & Crafts Message Board.

        Take a few minutes to read through them. They are chock full of great information.

        Be sure and share pics of your projects. We thrive on pictures. You will find we are not a judgmental group.

        Whatever reason brought you to our forum we are pleased you found us.

        Take some time to read the bylaws of the forum. We do not allow open/direct selling on the forum.
        "Still Montana Mike"

        "Don't worry about old age--it doesn't last that long."
        Mike's Wood-n-Things LLC

        Comment


        • #5
          Welcome "a-board" Pete, would love to see some of your work.......21 years is a lot of experience.
          Gloria ............... Two memorable things to say in life, "Hello" for the first time, and "Good-bye" for the last.

          Comment


          • #6
            Welcome Pete. Anxious to see your work.
            ichibob
            aka - Bob, USAF Ret.
            www.grandpaswoodshed.com

            Comment

            Unconfigured Ad Widget

            Collapse

            Latest Topics

            Collapse

            • MidMich324
              Reply to hegner 2"
              by MidMich324
              Just Wondering...

              Is the table size on the 22" hegner saw as on the 18" hegner saw?

              With the 22" inch one you get 4 more inches of depth of cut but do you also get a few more inches of table?
              Yesterday, 09:30 PM
            • will8989
              Reply to Spring Issue
              by will8989
              I had to fool around with copying and taping a pattern again today. This wasn’t as bad as the fish, but still a pain. I use rapid resizer. Scan a pattern, put in size I want and it prints it out. If more than one page, it numbers each page at the top and I tape them together. Had the fish pattern...
              Yesterday, 09:28 PM
            • millwab
              Reply to Peanuts #1
              by millwab
              Rolf, I cover it with clear contact paper (comes off clean without leaving a residue) and draw a grid for the direction I want to cut (ie horizontal or diagonal) to keep the rows even. The rest is all freehand....
              Yesterday, 02:51 PM
            • Don in Brooklin On
              Reply to Spring Issue
              by Don in Brooklin On
              Rolf

              I use acrobat reader. The poster feature will enlarge and if it goes to multiple pages it will put in cut marks. Even if the page is over letter size it will spread to multiple pages at 100%.

              If it is in PDF form you can open with Inkscape or GIMP and select what you...
              Yesterday, 01:48 PM
            • theframer
              Reply to YoraHome Laser w/CNC Engraver/Router
              by theframer
              Hi Linda, great find...I think.

              Please keep us up to date with any information you receive. I would really like to get into this, but my computer skills are almost nonexistent, I need something that a 74 year old air head 🙄 can figure out. Thanks for sharing.

              Rick
              Yesterday, 12:05 PM
            Working...
            X