Announcement

Collapse
No announcement yet.

2011 calendar's for sale where?

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
  • #1

    2011 calendar's for sale where?

    Hello all,
    I know this site was posted before but I can't find it. What is the site to buy 2011 and older calendar's for sale? Thanks.
    Mark
    Proud new owner of an EX-21

    WWW.MGMWOODWORKS.COM

    Tags: None
  • #2
    Calendars.com
    "Still Montana Mike"

    "Don't worry about old age--it doesn't last that long."
    Mike's Wood-n-Things LLC

    Comment

    • #3
      Thanks Mike.
      Proud new owner of an EX-21

      WWW.MGMWOODWORKS.COM

      Comment

      • #4
        No problem.
        "Still Montana Mike"

        "Don't worry about old age--it doesn't last that long."
        Mike's Wood-n-Things LLC

        Comment

        • #5
          Just given me an idea, my local newsagency is selling 2011 calendars cheap to get rid of them, they have some good pictures of Australian animals, flowers and scenery. I might have to grab a few and try making a tray puzzle with them

          Is there any copyright issue I should be aware of if I use a calendar picture for a tray puzzle?
          Last edited by Oges; 09-19-2011, 03:54 PM. Reason: Adding a question
          Brett

          Only Robinson Crusoe could get everything done by Friday!

          Comment

          • #6
            Brett, no problem if you don't sell or advertise to sell your work, but if you do, better pay attention to both U.S. and Australian laws. Good luck.....

            Carter

            Comment

            Previous template Next

            Unconfigured Ad Widget

            Collapse

            Latest Topics

            Collapse
            • handibunny
              Reply to EX dust collection holes screwed up a project.!
              by handibunny
              Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
              Today, 09:21 AM
            • Bill Wilson
              Reply to EX dust collection holes screwed up a project.!
              by Bill Wilson
              I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
              Today, 09:06 AM
            • cwmagee
              Reply to EX dust collection holes screwed up a project.!
              by cwmagee
              Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
              Today, 08:40 AM
            • Rolf
              Reply to EX dust collection holes screwed up a project.!
              by Rolf
              That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
              Today, 07:28 AM
            • handibunny
              Reply to EX dust collection holes screwed up a project.!
              by handibunny
              Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
              Today, 06:21 AM
            View All
            Working...
            X