Announcement

Collapse
No announcement yet.

Military Plaque - Army

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Military Plaque - Army

    I purchased the book 'U.S. Military Designs 2nd edition' by Mike and Vicky Lewis from Fox Chapel. This is the first of hopefully many. I used 1/4" Baltic Birch plywood and backed with 1/4" Baltic Birch plywood stained blue. The middle is stained walnut. I enlarged the pattern by 20% to make a 9" plaque. I used FD UR #1 blades and three coats of spray Polyurethane. You can't see from the picture, but there are three layers each raised y 1/8" with spacers. Comments welcome.
    Denny
    ArtCrafters in Dayton, TN

  • #2
    Nice cutting! These are my best salers. That reminds me I have to make some more for the Air Force.

    Comment


    • #3
      Originally posted by Trackman View Post
      Nice cutting! These are my best salers. That reminds me I have to make some more for the Air Force.
      Thanks. I am not sure how the second edition differs than the first edition, but I like them.
      Denny
      ArtCrafters in Dayton, TN

      Comment


      • #4
        Well done, only way it could be better would be if it was Marine Corps.
        AKA Paul from Washington State

        Comment


        • #5
          Denny,

          That is impressive! As usual your workmanship is a 10+

          cwmagee
          aka Fibber
          Producer of fancy firewood​

          Comment


          • #6
            Really nice! Can you take an angled picture to show the different elevations.?
            Rolf
            RBI G4 Hawk, Delta SS350, Nova 1624 DVR XP
            Philosophy "I don't know that I can't, therefore I can"
            Proud Member of the Long Island Woodworkers Club
            And the Long Island Scrollsaw Association

            Comment


            • #7
              I'm with Fibber 10+ job as always. I really like the different color and dimension added by the spacers too. Did you do that on your own or did the pattern call for doing that?
              Melanie from East TN

              Comment


              • #8
                Originally posted by Rolf View Post
                Really nice! Can you take an angled picture to show the different elevations.?
                Thanks Rolf. Here is the picture.
                Denny
                ArtCrafters in Dayton, TN

                Comment


                • #9
                  Originally posted by meflick View Post
                  I'm with Fibber 10+ job as always. I really like the different color and dimension added by the spacers too. Did you do that on your own or did the pattern call for doing that?
                  Thanks Melanie. The book calls for the spacers. Not sure if the first edition is the same.
                  Denny
                  ArtCrafters in Dayton, TN

                  Comment


                  • #10
                    very nice cutting, RJ
                    Life Begins @ 190 MPH

                    Comment


                    • #11
                      Denny
                      Nice cutting. When I was doing shows these were among my best sellers. I used 1/8 BB ply and used acid free paper for the colored part. Keep up the good work!

                      Comment


                      • #12
                        Thanks everyone for the nice comments.
                        Denny
                        ArtCrafters in Dayton, TN

                        Comment


                        • #13
                          Thanks for the side view.
                          Rolf
                          RBI G4 Hawk, Delta SS350, Nova 1624 DVR XP
                          Philosophy "I don't know that I can't, therefore I can"
                          Proud Member of the Long Island Woodworkers Club
                          And the Long Island Scrollsaw Association

                          Comment


                          • #14
                            Impressive as always, Denny. That will make some vet really happy.
                            Tony

                            My Son-in-law said "Darnit, I cut this board twice, now. And it's still too short."

                            Comment


                            • #15
                              Thanks for the nice comments. I now have requests for Marines and Air Force.
                              Denny
                              ArtCrafters in Dayton, TN

                              Comment

                              Unconfigured Ad Widget

                              Collapse

                              Latest Topics

                              Collapse

                              Working...
                              X