Announcement

Collapse
No announcement yet.

Daisy the cow.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Daisy the cow.

    Give me your opinions on my Kitchen roll holder.I am still learning the art of scroll sawing.
    Attached Files
    Learning the art of scroll saw.

  • #2
    Your going to need lots of paper towels because the cow is spilling all her milk laying sideways like that .....but from that angle looks like you did a nice scrolling and painting job.
    Thanks for posting yer pix.
    Gloria ............... Two memorable things to say in life, "Hello" for the first time, and "Good-bye" for the last.

    Comment


    • #3
      We will name it "Sleeping Cow" Great job of cutting and painting...something most of us can do one or the other but not both....I am the scroller and my wife the painter in my family.

      Are these coming back around again? I remember making tons of these years ago
      Hawaiilad
      Larry

      Comment


      • #4
        Its definitely tilted to one side quite a bit. Looks like you did a fine job with it.
        Douglas Fraser
        Eagle River, Alaska

        My Gallery - Aurora Wood Crafts

        Comment


        • #5
          The head in the pattern was on the side like that.Keep those comments coming.I am still learning.
          Learning the art of scroll saw.

          Comment


          • #6
            We weren't talking about the cute tilted cow head...it's the picture that is side ways. Just poking a little fun is all
            Hawaiilad
            Larry

            Comment


            • #7
              I love this, its so cute! I could definitely see this in a country kitchen somewhere...

              Comment


              • #8
                Good job cutting and painting. My wife would like one of those. Did you purchase a pattern somewhere?
                Pacifism is great, as long as everyone is participating.



                StephenD


                The Southern Arizona Woodturners Association
                Desert Woodcrafters
                Grandpa for the 7 most amazing children.

                Comment


                • #9
                  good job looks fine to me Ron

                  Comment

                  Unconfigured Ad Widget

                  Collapse

                  Latest Topics

                  Collapse

                  • MidMich324
                    Reply to hegner 2"
                    by MidMich324
                    Just Wondering...

                    Is the table size on the 22" hegner saw as on the 18" hegner saw?

                    With the 22" inch one you get 4 more inches of depth of cut but do you also get a few more inches of table?
                    Yesterday, 09:30 PM
                  • will8989
                    Reply to Spring Issue
                    by will8989
                    I had to fool around with copying and taping a pattern again today. This wasn’t as bad as the fish, but still a pain. I use rapid resizer. Scan a pattern, put in size I want and it prints it out. If more than one page, it numbers each page at the top and I tape them together. Had the fish pattern...
                    Yesterday, 09:28 PM
                  • millwab
                    Reply to Peanuts #1
                    by millwab
                    Rolf, I cover it with clear contact paper (comes off clean without leaving a residue) and draw a grid for the direction I want to cut (ie horizontal or diagonal) to keep the rows even. The rest is all freehand....
                    Yesterday, 02:51 PM
                  • Don in Brooklin On
                    Reply to Spring Issue
                    by Don in Brooklin On
                    Rolf

                    I use acrobat reader. The poster feature will enlarge and if it goes to multiple pages it will put in cut marks. Even if the page is over letter size it will spread to multiple pages at 100%.

                    If it is in PDF form you can open with Inkscape or GIMP and select what you...
                    Yesterday, 01:48 PM
                  • theframer
                    Reply to YoraHome Laser w/CNC Engraver/Router
                    by theframer
                    Hi Linda, great find...I think.

                    Please keep us up to date with any information you receive. I would really like to get into this, but my computer skills are almost nonexistent, I need something that a 74 year old air head 🙄 can figure out. Thanks for sharing.

                    Rick
                    Yesterday, 12:05 PM
                  Working...
                  X