Announcement

Collapse
No announcement yet.

Where can we find 3D snowflake patterns

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Where can we find 3D snowflake patterns

    That are free to print out? I have searched the net but can't seem to find anything that is free. Thank you for your help. Happy scrollin'!

  • #2
    I don't know of any free patterns but if you go to this link you will see a really nice one for sale.

    Snowflake Pattern
    Todd

    Hawk G4, Dremel 1800

    Quando Omni Flunkus Moritati

    Comment


    • #3
      I found the magazine with the pattern of the 16 piece snowflake in it was in Creative Woodworks & Crafts, Oct. of 2001. If you have that one, it needs to be downsized. I made it out of 1/8" baltic birch.

      I hope this is of some help to you.
      Bob
      Delta P-20 & Q-3

      I wondered why the baseball was getting bigger. Then it hit me!

      Comment


      • #4
        Thank you bunches!

        Cassandra

        Comment


        • #5
          That's the beauty of this forum, everyone here is out to help the next person.
          Todd

          Hawk G4, Dremel 1800

          Quando Omni Flunkus Moritati

          Comment


          • #6
            Todd, how is the weather up there?
            Bob
            Delta P-20 & Q-3

            I wondered why the baseball was getting bigger. Then it hit me!

            Comment


            • #7
              The weather is always great, currently we are dying from a 70 degree heat wave, and I ain't kidding.
              Todd

              Hawk G4, Dremel 1800

              Quando Omni Flunkus Moritati

              Comment


              • #8
                3D pattern

                I knew Ihad seen a pattern somehwere. Right under my nose!

                Pattern
                In the free pattern section of this forum.
                It is called a snowball but it is 3D and looks like a Snowflake to me.... But I took my glasses off to write this
                CAЯL HIRD-RUTTEЯ
                "proud member of the best scroll sawing forum on the net."
                Ryobi SC180VS scroll saw EX21

                Comment


                • #9
                  Since I don't know how to post pictures in this forum you can go here and see it.
                  Bob

                  http://wmyoung.proboards23.com/index...ead=1118534522
                  Delta P-20 & Q-3

                  I wondered why the baseball was getting bigger. Then it hit me!

                  Comment


                  • #10
                    Thank you Carl! That is great! My husband will love it! Thank you to everyonel I hope ya have a great day!

                    Cassandra

                    Comment

                    Unconfigured Ad Widget

                    Collapse

                    Latest Topics

                    Collapse

                    • Rolf
                      Reply to My covid angel
                      by Rolf
                      Great designe! I would have gone a bit further than Linda, Scott and Gladefade I would cut it into more pieces to make shaping easier. Taper the clouds from right to left, taper the wings so that they are lower where they attach to the body. Taper the neck so that it looks like it is going into the...
                      Today, 09:02 AM
                    • Rolf
                      Reply to Tough Decisions
                      by Rolf
                      The never ending dilemma. I only get two magazines SSWWC and Wood carving Illustrated. Even if I don't make something in every issue there is usually something in each one that I have never tried and that will either challenge or inspire me. Yes I know that I do test cutting for them and they have occasionally...
                      Today, 08:49 AM
                    • NC Scroller
                      Reply to My covid angel
                      by NC Scroller
                      I would start by tracing your piece on a piece of 1/8" (3mm) material and then cut the back our such that it is a fraction smaller that your project. Then I would cut your piece into two pieces. I mean cut the angel from the cloud. I would then put the cloud on the 1.8" backer and then with...
                      Today, 07:27 AM
                    • Quartz43
                      Reply to Tough Decisions
                      by Quartz43
                      I understand supporting the magazine and agree. I just do not find many projects that fit my desires.

                      I would like to see them do a poll with subscribers to find out what type projects people want to see....
                      Today, 05:42 AM
                    • GladeFade
                      Reply to My covid angel
                      by GladeFade
                      First off how thick is the board you cut?
                      When I want something to stand out I use backer-boards 1/8 thick to get the depth.
                      that means you would have to cut the big cutting into pieces to put the spacer behind.
                      for instance the cloud bottom right which his hand is on I would put maybe...
                      Yesterday, 11:05 PM
                    Working...
                    X