Announcement

Collapse
No announcement yet.

Puerto Rico

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Puerto Rico

    This pattern is by Sam Custodio and found on his FaceBook page. A perfect gift for our ArtCrafters neighbors who own a café on the corner. I used 1/2" Bloodwood and backed with 1/4" Baltic Birch plywood stained blue with Saman stain. It is approximately 6" x 16". I used FD Polar #1 and New Spiral #5 blades. The finish is spray Shelac. Comments welcome.
    Denny
    ArtCrafters in Dayton, TN

  • #2
    Very nice work as always Denny, your neighbor should really like it, RJ
    Life Begins @ 190 MPH

    Comment


    • #3
      Originally posted by RJweb View Post
      Very nice work as always Denny, your neighbor should really like it, RJ
      Thanks RJ. Just gave it to them and got two wonderful hugs.
      Denny
      ArtCrafters in Dayton, TN

      Comment


      • #4
        Ahh the hugs are priceless!
        It came out great.
        Rolf
        RBI G4 Hawk, Delta SS350, Nova 1624 DVR XP
        Philosophy "I don't know that I can't, therefore I can"
        Proud Member of the Long Island Woodworkers Club
        And the Long Island Scrollsaw Association

        Comment


        • #5
          Originally posted by Rolf View Post
          Ahh the hugs are priceless!
          It came out great.
          Thanks Rolf. I agree with the hugs!
          Denny
          ArtCrafters in Dayton, TN

          Comment


          • #6
            A treasured gift that will last a lifetime. Beautiful.
            Linda at www.ArtIngrained.com

            Comment


            • #7
              Thanks Linda
              Denny
              ArtCrafters in Dayton, TN

              Comment


              • #8
                Hugs--the universal currency.
                Great work and love the color.
                Jim
                When looking at the clock at work--the correct time is:
                Too early to leave, too late to call in.

                Comment


                • #9
                  Thanks Jim
                  Denny
                  ArtCrafters in Dayton, TN

                  Comment

                  Unconfigured Ad Widget

                  Collapse

                  Latest Topics

                  Collapse

                  • Sandy Oaks
                    Reply to Colwood wood burner Great support
                    by Sandy Oaks
                    Good to hear about great service and support
                    Today, 09:14 AM
                  • Rolf
                    Colwood wood burner Great support
                    by Rolf
                    I was using my older Colewood Super pro II yesterday and I could not control the temperature. As soon as I turned it on the tip went to the max. I opened it up to have a look.
                    Not much in the box a Transformer, a small circuit board with a few components. I decided to call the company and I believe...
                    Today, 08:27 AM
                  • Rolf
                    Reply to ?????? ??
                    by Rolf
                    It seems that new members don't present themselves in the new members section. If anyone spots a new member encourage them to introduce themselves in the new member section.

                    I will send Kaylee a note to see who is overseeing the forum.
                    Today, 08:06 AM
                  • Jim McDonald
                    Reply to ?????? ??
                    by Jim McDonald
                    As you know, we lost a ton of folks during the time the board was being redone and a lot of them ended up at the Village and have never looked back.
                    As far as updates to the software, I am with Scott on having no clue. I do wish some of the old timers would check in from time to time, even...
                    Yesterday, 07:43 PM
                  • NC Scroller
                    Reply to ?????? ??
                    by NC Scroller
                    I know Bob Duncan used to monitor and work on forum issues. No clue who is handling it now....
                    Yesterday, 05:37 PM
                  Working...
                  X