Announcement

Collapse
No announcement yet.

Butterfly Crosses

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Butterfly Crosses

    Just finished some Butterfly Crosses, Cedar, Walnut and Red Oak (not sure who the designer is). The cowboy portrait is another great one by Charles Dearing.
    Brian in the Four Corners

  • #2
    Very Nice!
    ♥♥ ♫ ♪ ♫ ♥♥

    Comment


    • #3
      Beautiful work. thanks for sharing. If you can figure out the designer or where you got the butterfly cross pattern I would like to try and obtain it and give one a try. Perhaps someone else will know and can point us in the right direction.
      Melanie from East TN

      Comment


      • #4
        Pleas let me know where I can get the pattern, Thanks

        Comment


        • #5
          You can get the pattern off the Wooden Teddy Bear web site.
          Brian in the Four Corners

          Comment


          • #6
            Originally posted by bcdennis View Post
            You can get the pattern off the Wooden Teddy Bear web site.
            Thanks Brian for letting us know where to get it. For those looking, here is the direct link to it:
            http://www.woodenteddybearonline.com...68&cat=&page=1
            Melanie from East TN

            Comment


            • #7
              Those are quite intricate and unusual. Coolness.
              Linda at www.ArtIngrained.com

              Comment


              • #8
                That is beautiful. Getting pattern.
                Betty

                "Congress needs to realize it is a government of the people, by the people and for the people. Not of the people, by the people and for Congress." - Dr. Benjamin Carson, Pediatric Neurosurgeon, Johns Hopkins Hospital

                Comment


                • #9
                  Nice! Very neat.

                  Comment

                  Unconfigured Ad Widget

                  Collapse

                  Latest Topics

                  Collapse

                  • NC Scroller
                    Reply to Local craft fair very disappointing.
                    NC Scroller
                    Sad but seeing this trend more and more. I think there are several reasons. In general fewer people are interested in hand crafted goods made by local artists. They see what they like and buy it no matter if I was hand crafted locally or commercially produced. Second the made overseas stuff is cheaper...
                    Today, 07:43 AM
                  • WynnD
                    Reply to Confused "newbie", here!
                    WynnD
                    The set screw Carole mentioned is opposite the blade tightening knob. She is correct the screws will make the blade be off center. I had only one problem with the DW. There is a fitting on the end oif the motor arm. Mine came loose and made a racket. I followed the video you mentioned and it was very...
                    Today, 06:40 AM
                  • handibunny
                    Reply to Confused "newbie", here!
                    handibunny
                    Start by retracting the set screw fully on both upper and lower clamps, then turn them each the same amount until they have protruded enough to grab the blade when you tighten the thumb screw. If for some reason the blade is still not completely perpendicular, adjust them until it is. Should not be...
                    Today, 06:08 AM
                  • will8989
                    Reply to Local craft fair very disappointing.
                    will8989
                    A lot of fairs in this area are going back to the way it used to be meaning you need to submit pictures of your work and some equipment. A lot of promoters are also visiting craft shows and talking to vendors and asking them to apply for their show. this is my 3rd year at the howard county 3 day show...
                    Today, 12:12 AM
                  • cwmagee
                    Reply to Confused "newbie", here!
                    cwmagee
                    If my memory is correct you have a set screw on the left side of blade clamp and the thumb screw on the right side on both upper and lower blade clamps. If you do not adjust both set screws so they are the same (just proud of blade clamp slot), your blade will not be square.
                    Yesterday, 10:01 PM
                  Working...
                  X