Announcement

Collapse
No announcement yet.

Looking for pattern

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Looking for pattern

    I am on the search for a Coke pattern. Anyone have any ideas where I can get one that is not too complex? I am a fairly new scroller so am looking for something that is not too difficult, yet.
    Sherri

  • #2
    Did you try looking at the MSN free pattern groups, Doodle1? I don't recall seeing one there but they have a lot of patterns .... I doubt that there are commercial patterns available - for trademark/copyright reasons, but I could be wrong.

    Try http://groups.msn.com/FreeScrollsawPatterns or http://groups.msn.com/absolutelyfreescrollsawpatterns
    Ian

    Scrolling with a Dewalt 788

    Comment


    • #3
      I'm a member of Absolutelyfree and I'm sure they have had a coke pattern in there. Do a search on the website.
      Diane
      Dragon
      Owner of a nice 21" Excalibur
      Owner of a Dewalt 788
      PuffityDragon on AFSP

      Comment


      • #4
        Thanks for the info. I'll try that!
        Sherri

        Comment


        • #5
          I'm doubting anyone will have a free coca cola pattern. That's a pretty strict copyright. I could be wrong, but the person giving that away would have to be insane. It would be hard to believe they got permission.
          You could certainly make your own pattern...just be sure not to be selling it out to the public.
          Jeff Powell

          Comment

          Unconfigured Ad Widget

          Collapse

          Latest Topics

          Collapse

          • handibunny
            Reply to EX dust collection holes screwed up a project.!
            by handibunny
            Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
            Today, 09:21 AM
          • Bill Wilson
            Reply to EX dust collection holes screwed up a project.!
            by Bill Wilson
            I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
            Today, 09:06 AM
          • cwmagee
            Reply to EX dust collection holes screwed up a project.!
            by cwmagee
            Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
            Today, 08:40 AM
          • Rolf
            Reply to EX dust collection holes screwed up a project.!
            by Rolf
            That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
            Today, 07:28 AM
          • handibunny
            Reply to EX dust collection holes screwed up a project.!
            by handibunny
            Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
            Today, 06:21 AM
          Working...
          X