Announcement

Collapse
No announcement yet.

A few bits and pieces ..

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • A few bits and pieces ..

    A few things I've done this week - and actually put some finish on .. lol
    Attached Files
    Last edited by PuzzledMoose; 01-04-2007, 03:13 PM.
    Ian

    Scrolling with a Dewalt 788

  • #2
    They all look good, I think I like the next to the last one best.
    Bill

    DeWalt 788



    aut viam inveniam aut faciam

    God gives us only what we can handle.. Apparently God thinks I am one tough cookie.....

    Comment


    • #3
      Nice work. They are all nice.
      Dragon
      Owner of a nice 21" Excalibur
      Owner of a Dewalt 788
      PuffityDragon on AFSP

      Comment


      • #4
        smashing work ian.
        kevin/pitbull.

        Comment


        • #5
          Nice work Ian, I like the "Dog did it" message, it's perfect.
          Todd

          Hawk G4, Dremel 1800

          Quando Omni Flunkus Moritati

          Comment


          • #6
            Originally posted by ozarkhillbilly
            I think I like the next to the last one best.
            You've got cheap tastes, Bill, lol. That's the one that's made from MDF - 3/4 inch on the backing board and 1/4 inch for the cutting - it isn't a particularly good photo - the backer isn't curved! - but I kinda like the look of it - the design is one from a Spielman book and its just got a couple of coats of gold paint sprayed on it ...
            Ian

            Scrolling with a Dewalt 788

            Comment


            • #7
              Originally posted by PuzzledMoose
              You've got cheap tastes, Bill, lol. That's the one that's made from MDF - 3/4 inch on the backing board and 1/4 inch for the cutting - it isn't a particularly good photo - the backer isn't curved! - but I kinda like the look of it - the design is one from a Spielman book and its just got a couple of coats of gold paint sprayed on it ...
              Ahem!

              I was going to post nice comments about your projects until I read this. You've just dissed my entire repertoire!



              Gill
              There is no opinion, however absurd, which men will not readily embrace as soon as they can be brought to the conviction that it is readily adopted.
              (Schopenhauer, Die Kunst Recht zu Behalten)

              Comment


              • #8
                Originally posted by Gill
                Ahem!

                I was going to post nice comments about your projects until I read this. You've just dissed my entire repertoire!



                Gill
                ROTFL - you know I thought of you, Gill, when I typed that bit about the MDF
                Ian

                Scrolling with a Dewalt 788

                Comment

                Unconfigured Ad Widget

                Collapse

                Latest Topics

                Collapse

                • Misouri Wayne
                  Reply to Spiral Blades - Tips & Tricks?
                  by Misouri Wayne
                  Thanks for the post. I have tried spirals in the past and had lots of issues. I need to set down one day and keep cutting with them until I get the hang of it. Part of my problem may have been covered by your number 7. Tried pine thinking it would be easy to cut but now realize the grain may have...
                  Today, 07:05 PM
                • Sandy Oaks
                  Reply to Eagle
                  by Sandy Oaks
                  I agree, a beautiful piece and wonderful cutting. Years ago, my father had Alzheimer. The last six months we had him in the VA center in St. Cloud MN. His wood work shop is still in MN. I could not take it down to TN....
                  Today, 12:00 PM
                • Rolf
                  Reply to Spiral Blades - Tips & Tricks?
                  by Rolf
                  I have been using spiral a lot more lately Thanks to Charles Hand stunning designs. I have used them of and on since I started scrolling.
                  They were a real challenge on my Old Delta SS350. cutting straight in and out was easy, trying to cut details going sideways was the problem because of the...
                  Today, 09:16 AM
                • Jimern
                  Reply to Spiral Blades - Tips & Tricks?
                  by Jimern
                  The best tip I have with spirals is to cut straight lines backwards. instead of pushing the work piece into the blade, pull it toward you. Seems to allow for better control on straight lines (most other lines too)
                  Today, 05:27 AM
                • Linda In Phoenix
                  Reply to Mexican Covid19 Vaccination logo - my version :)
                  by Linda In Phoenix
                  Go Wylie Coyote!!!
                  Yesterday, 09:19 PM
                Working...
                X