Announcement

Collapse
No announcement yet.

Knight on Horseback

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Knight on Horseback

    pattern by Bob Valle. knight was cut from 1/4" B.B. and the backer was cut from 3/4" pine stained English Chestnut.

    Pat...

  • #2
    That looks good. I don't know if I'd have the patience for all those little straight lines.
    My Gallery

    Comment


    • #3
      looks good PAT,
      well done
      not doing much
      and busy doing it


      having fun making sawdust.


      http://www.customcutz4you.webs.com/

      Comment


      • #4
        Beautiful piece, Pat. Looks fantastic. Love the grain in the backer, with the English Chestnut stain. You did good !
        PERK

        Comment


        • #5
          Well done project! God Bless! Spirithorse

          Comment


          • #6
            Very nice Pat!!!
            May the wind at you back .....
            Not be from Lunch.

            Don't take life too seriously; No one gets out alive.

            Beauty is in the eye of the BEERHOLDER

            Visit My Gallery

            Oily's Gallery

            http://www.picturetrail.com/oily11

            Comment


            • #7
              Pat, that is great looking!
              Dan

              My Gallery

              Comment


              • #8
                that is really nice.

                Comment

                Unconfigured Ad Widget

                Collapse

                Latest Topics

                Collapse

                • handibunny
                  Reply to EX dust collection holes screwed up a project.!
                  by handibunny
                  Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
                  Today, 09:21 AM
                • Bill Wilson
                  Reply to EX dust collection holes screwed up a project.!
                  by Bill Wilson
                  I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
                  Today, 09:06 AM
                • cwmagee
                  Reply to EX dust collection holes screwed up a project.!
                  by cwmagee
                  Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
                  Today, 08:40 AM
                • Rolf
                  Reply to EX dust collection holes screwed up a project.!
                  by Rolf
                  That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
                  Today, 07:28 AM
                • handibunny
                  Reply to EX dust collection holes screwed up a project.!
                  by handibunny
                  Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
                  Today, 06:21 AM
                Working...
                X