Announcement

Collapse
No announcement yet.

Deer Plaque

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Deer Plaque

    I made this for my manager at work.
    Linda

  • #2
    Linda, Your manager is very lucky. I like the design with the deer offset. The cutting and finish is very well done.
    Lois

    Comment


    • #3
      aye, very nice, I am a sucker for finishes and I like yours, nice and silky.
      The Journey Is Everything.

      http://www.sunlion-pyrography.co.uk/

      My Google+

      Comment


      • #4
        I love it, where did you find the pattern?

        Comment


        • #5
          That's very nice! Great job Linda.
          Dan

          My Gallery

          Comment


          • #6
            Gorgeous.....way too nice for a manager.

            Comment


            • #7
              The pattern is signed Dave Hall, but it doesn't say which site it came from.
              Linda

              Comment


              • #8
                Very nice Linda, to nice to give away. Edward
                http://www.scrollsawer.com/gallery/s...00&ppuser=6384

                Comment


                • #9
                  Super job, well done
                  Mike

                  Mike Fehring's Artistry in Wood
                  http://www.mikefehring.com
                  Mike Fehring's Free Patterns

                  Comment


                  • #10
                    Like this .. pretty work Linda ..........
                    Usually busier than a cat in a sandbox !!!!!!!!!!! MB { Dewalt 788 only }

                    Comment


                    • #11
                      Very nice, checked my Dave Hall books and it was not in any of them. Darn...
                      Chuck D


                      When a work lifts your spirits and inspires bold and noble thoughts in you, do not look for any other standard to judge by: the work is good, the product of a master craftsman.
                      Jean De La Bruyere...

                      l
                      Hegner 18, Delta p-20, Griz 14 inch Band saw

                      Comment

                      Unconfigured Ad Widget

                      Collapse

                      Latest Topics

                      Collapse

                      • handibunny
                        Reply to EX dust collection holes screwed up a project.!
                        by handibunny
                        Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
                        Today, 09:21 AM
                      • Bill Wilson
                        Reply to EX dust collection holes screwed up a project.!
                        by Bill Wilson
                        I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
                        Today, 09:06 AM
                      • cwmagee
                        Reply to EX dust collection holes screwed up a project.!
                        by cwmagee
                        Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
                        Today, 08:40 AM
                      • Rolf
                        Reply to EX dust collection holes screwed up a project.!
                        by Rolf
                        That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
                        Today, 07:28 AM
                      • handibunny
                        Reply to EX dust collection holes screwed up a project.!
                        by handibunny
                        Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
                        Today, 06:21 AM
                      Working...
                      X