Announcement

Collapse
No announcement yet.

Arrowhead Wolves

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Arrowhead Wolves

    It was cut from a piece of 3/8" pine stained Golden Oak with a 3/4" backer stained Dark Walnut. The pattern is by Micheal Hornung.

    Pat...
    Attached Files

  • #2
    I like that ,nice job.
    Hegner Polymax- 3,Hegner Multimax-3,
    "No PHD, just a DD 214"

    Comment


    • #3
      That is great work.

      Bob
      Delta P-20 & Q-3

      I wondered why the baseball was getting bigger. Then it hit me!

      Comment


      • #4
        That looks great ! I like the depth perception that you gave it. Good Job.
        PERK

        Comment


        • #5
          That is really nice. I like it very much
          May the wind at you back .....
          Not be from Lunch.

          Don't take life too seriously; No one gets out alive.

          Beauty is in the eye of the BEERHOLDER

          Visit My Gallery

          Oily's Gallery

          http://www.picturetrail.com/oily11

          Comment


          • #6
            Great cutting Pat. I too like the layer look.
            Dan

            My Gallery

            Comment


            • #7
              Pat, Very nice cutting. Like it a lot. What size is it and how much would it sell for? Lance

              Comment


              • #8
                Nice cutting Pat.
                Linda

                Comment


                • #9
                  Nice work, little paw especially a nice touch.
                  I made some similar out of exotic wood some time back

                  Comment


                  • #10
                    Very nice workmanship!
                    DeWalt 788

                    Comment


                    • #11
                      I can see a bunch of these cut and giving out for presents too , this is sharp looking ............MB
                      Usually busier than a cat in a sandbox !!!!!!!!!!! MB { Dewalt 788 only }

                      Comment


                      • #12
                        Where can i find or buy that pattern?

                        It's all fun
                        Terry
                        Craftsman 18"
                        Delta 46-460 lathe
                        ________________________

                        https://www.facebook.com/SillyLillyBowsAndMore

                        Comment


                        • #13
                          Thanks everyone.
                          Pat...

                          Comment

                          Unconfigured Ad Widget

                          Collapse

                          Latest Topics

                          Collapse

                          • NC Scroller
                            Reply to My covid angel
                            by NC Scroller
                            Whatever way you decide to do if you are happy and your brother in law is happy it was a good idea. If you really want to be brave use it as a learning experience. Make several of them using different suggestions and see the difference....
                            Today, 12:35 PM
                          • Bill Wilson
                            Reply to Tough Decisions
                            by Bill Wilson
                            Well, unfortunately, I have also decided to let my subscription lapse. I've been debating it for the past couple years. It isn't so much the money, but it's more the disappointment when yet another issue has so little in it that really appeals to me. The final straw was this past Fall/Winter edition...
                            Today, 09:51 AM
                          • planeur
                            Reply to My covid angel
                            by planeur
                            Thanks to all !😀 Your comment are very good and make sense!

                            My piece is 8"X8" X 1/2" thick.
                            I though when I cutted the piece to do it in 1 piece or 4/5 , but after a while I decided to do it in one piece and carved it to have a 3D aspect.
                            Was it a good idea.....?...
                            Today, 09:45 AM
                          • Rolf
                            Reply to My covid angel
                            by Rolf
                            Great designe! I would have gone a bit further than Linda, Scott and Gladefade I would cut it into more pieces to make shaping easier. Taper the clouds from right to left, taper the wings so that they are lower where they attach to the body. Taper the neck so that it looks like it is going into the...
                            Today, 09:02 AM
                          • Rolf
                            Reply to Tough Decisions
                            by Rolf
                            The never ending dilemma. I only get two magazines SSWWC and Wood carving Illustrated. Even if I don't make something in every issue there is usually something in each one that I have never tried and that will either challenge or inspire me. Yes I know that I do test cutting for them and they have occasionally...
                            Today, 08:49 AM
                          Working...
                          X