Announcement

Collapse
No announcement yet.

Hockey player done

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Hockey player done

    I cut this hockey player out for my oldest grandson. I used red felt for the background.

    The pattern of the player is by Sue Mey and the word Chicago was taken from a Steve Good pattern.
    Attached Files

  • #2
    nice work, Trackman!
    I don't answer to your question about felt for backer because I prepare 4 craft show that will be between 25 November and 10 december... I need a lot of things...
    sometime I put cardboard at the back of scrollsaw (for flowers) or a small canvas trie (put) on small plate of wood thickness 1/8" (3mm) thzt I screw on the scrollsaw. Canvas or felt is similar problem to install at the back of your project...
    Best regards

    Simon MARTIN
    From France

    Visit My Gallery:Simon's Album

    You can also look at my pyrography galery: Martin's Album
    Website: http://decors.bois.peinture.free.fr

    Comment


    • #3
      It turned out fine Trackman...mighty fine .........
      Usually busier than a cat in a sandbox !!!!!!!!!!! MB { Dewalt 788 only }

      Comment


      • #4
        Nice job. How did you attach the felt ? This question goes along with another thread requesting ways to do it.
        "Still Montana Mike"

        "Don't worry about old age--it doesn't last that long."
        Mike's Wood-n-Things LLC

        Comment


        • #5
          Mike- I used spray glue that I use to attach patterns to my boards than I used small nails to attach the board to the finished project. I think the felt helps it look like his uniform (some lol). It was my thread I think you are talking about. I was wanting to know best ways to attach. Thanks

          Comment


          • #6
            It turned out beautifully. Excellant job cutting and finishing that piece!
            Dale w/ yella saws

            Comment


            • #7
              Great job, your grandson is going to love it.
              Linda

              Comment


              • #8
                Go Blackhawks!! Nice! The red makes it pop in my opinion.
                Dan

                My Gallery

                Comment


                • #9
                  I gave it to him this afternoon an he realy liked it, he is a good kid lol. Thanks for all the nice words on the project.

                  Comment


                  • #10
                    That came out great!
                    Dan H

                    I would rather be friendly to a stranger than be a stranger to my friends.

                    Comment


                    • #11
                      Beautiful work, lucky grandson
                      Steve

                      Comment

                      Unconfigured Ad Widget

                      Collapse

                      Latest Topics

                      Collapse

                      • evilbadger
                        Reply to YoraHome Laser w/CNC Engraver/Router
                        by evilbadger
                        Yes I'm still using the one I built I did some upgrades to it though. I swapped out the pipes for linear motion rails and made the gantry out of aluminum. I guess if I were to upgrade now I would be looking for a full size machine that could do 4x8 sheets of plywood with an automatic tool changer but...
                        Today, 09:28 PM
                      • vgraf
                        Reply to Old Tool - Reborn
                        by vgraf
                        Looks great!
                        Today, 08:15 PM
                      • tgiro01
                        Old Tool - Reborn
                        by tgiro01
                        With all these new tool stories, I was working on and old one. About 9 years ago, I built a router table. Then, before it was finished, I had to start using it. And I have used it over the years. A couple of months ago, While I was contemplating cleaning, I looked at the machine and decided to finish...
                        Today, 03:24 PM
                      • Rolf
                        Reply to YoraHome Laser w/CNC Engraver/Router
                        by Rolf
                        I do remember that 2011 Wow, you were gutsy building that then, CNC was just coming into the home environment. Are you still using the one you built?
                        Today, 10:23 AM
                      • Rolf
                        Reply to Work in Progress. What is with FOX publishing?
                        by Rolf
                        Jim that is why there are now CD's available for past issues. To me a copier/scanner and printer are a necessary part of my tool inventory. JMO...
                        Today, 10:19 AM
                      Working...
                      X