Announcement

Collapse
No announcement yet.

Fruit Bowl

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Fruit Bowl

    Took the standard wobble bowl pattern (from Steve Goods site) and blew it up to roughly 12 inches in diameter to create this fruit bowl for my wife. Cut from scrap wood, finished in tung oil and 3 coats of clear poly.
    Attached Files
    ichibob
    aka - Bob, USAF Ret.
    www.grandpaswoodshed.com

  • #2
    Very nicely done Bob. That was a great use of a piece of scrap. Thanks for sharing this with us.

    DW
    Life is hard. It is even harder when you are being stupid.
    John Wayne

    Comment


    • #3
      Quite nice -- and big enough to hold some fruit. I don't consider any 12"X12" piece of wood "scrap" -- as it is an uncut project.
      Mtnman Jim

      taking life as it comes and trying to make the best of it

      Comment


      • #4
        Thanks DW...
        Jim, I have to agree with you about a 12 x 12 piece of wood being called 'scrap' LOL! This piece was an odd cut end piece off of a laminated board used for a table top - hence the term used. I don't think that I really look at any piece of wood as 'scrap'! Check out my wime basket from a 'chunk' of cabinet ply.
        ichibob
        aka - Bob, USAF Ret.
        www.grandpaswoodshed.com

        Comment


        • #5
          Good Bob and swell cutting and glue up job too ...............MB
          Usually busier than a cat in a sandbox !!!!!!!!!!! MB { Dewalt 788 only }

          Comment

          Unconfigured Ad Widget

          Collapse

          Latest Topics

          Collapse

          • keystonecop
            Had to post this just for Rolf.
            by keystonecop
            117 puzzles have had their first bath in watco natural oil. My yearly order from the store that buys from me.
            No I do not eat that much mayo....
            You do not have permission to view this gallery.
            This gallery has 1 photos.
            Today, 05:32 PM
          • Rolf
            Excalibur 21 repair #2
            by Rolf
            I just finished rebuilding my friends 2nd EX 21, This one was in much better shape than the first. No rusty bearings this time but I re-greased them anyway.
            I adjusted the front back motion and and the blade is also at 90 degrees to the table when using the locating pin.

            I used...
            Today, 02:44 PM
          • Bill Wilson
            Reply to Recommendations anyone?
            by Bill Wilson
            If it means the difference between cutting something and doing nothing, then go for it. It might not be the choice of most of us, but we aren't working under the same constraints as you. Hope it works out for you. Looking forward to a review, once you get a few miles on it.
            Yesterday, 02:42 PM
          • old fa_t
            Reply to Recommendations anyone?
            by old fa_t
            After totally over-thinking this, I have decided to go ahead with the Micro Mark Saw. It will enable me to do everything I can imagine in my limited space and budget.
            I thank everyone for offering advice, and I look forward to receiving more. As soon as I get it and set it up, I will post pictures...
            Yesterday, 07:37 AM
          • will8989
            Reply to Need any wood?
            by will8989
            Figured it out. The photos were Live and I had to edit them. As you can see, we were quite lucky they didn’t come crashing down in a storm. The last picture was a 2 trunk tree. My son already split a truck load today.

            Next project, the roofer next week. Yippee....
            04-20-2021, 08:56 PM
          Working...
          X