No announcement yet.

Spilled paint light done

  • Filter
  • Time
  • Show
Clear All
new posts

  • Spilled paint light done

    I picked up the kit to finish this up today thanks my sweet wife, I'm going to be working on the pattern in the next few days so give me a little time to get them out to you if you want to make this. thanks for looking hope you like it.Jerry

    Oh btw this would make a nice floor accent piece or table lamp.
    Attached Files
    Don't worry be scrolling

  • #2
    Cool looking light.

    Delta P-20 & Q-3

    I wondered why the baseball was getting bigger. Then it hit me!


    • #3
      Very nicely done Jerry. Thanks for sharing it with us.

      Life is hard. It is even harder when you are being stupid.
      John Wayne


      • #4
        That is so cool, Jerry! Looking forward to it!



        • #5
          Looks cool! thought there might be a splash of color in the paint...


          • #6
            Thanks glad you like it, Actually you can make this any color that you want I just happen to have a can of white paint when I did it thanks again.Jerry
            Don't worry be scrolling


            • #7
              That turned out very nice.
              "Still Montana Mike"

              "Don't worry about old age--it doesn't last that long."
              Mike's Wood-n-Things LLC


              • #8
                Nice looking and very unique.

                Karl in Sunny Southwest Florida


                • #9
                  Way to recycle! Thanks for sharing.

                  A day without sawdust is a day without sunshine.

                  delta 650, hawk G426


                  • #10
                    That is excellent. What a great idea.


                    • #11
                      Thanks again everyone I'm still working on the pattern, but the honey do list is more important so I will have it up as soon as I can,in fact it might be easier if you send me a PM with yur email and when I finish I will send it that way, this way it will only go to the people who really want it thanks again.Jerry
                      Don't worry be scrolling


                      Unconfigured Ad Widget


                      Latest Topics


                      • MidMich324
                        Reply to hegner 2"
                        by MidMich324
                        Just Wondering...

                        Is the table size on the 22" hegner saw as on the 18" hegner saw?

                        With the 22" inch one you get 4 more inches of depth of cut but do you also get a few more inches of table?
                        Yesterday, 09:30 PM
                      • will8989
                        Reply to Spring Issue
                        by will8989
                        I had to fool around with copying and taping a pattern again today. This wasn’t as bad as the fish, but still a pain. I use rapid resizer. Scan a pattern, put in size I want and it prints it out. If more than one page, it numbers each page at the top and I tape them together. Had the fish pattern...
                        Yesterday, 09:28 PM
                      • millwab
                        Reply to Peanuts #1
                        by millwab
                        Rolf, I cover it with clear contact paper (comes off clean without leaving a residue) and draw a grid for the direction I want to cut (ie horizontal or diagonal) to keep the rows even. The rest is all freehand....
                        Yesterday, 02:51 PM
                      • Don in Brooklin On
                        Reply to Spring Issue
                        by Don in Brooklin On

                        I use acrobat reader. The poster feature will enlarge and if it goes to multiple pages it will put in cut marks. Even if the page is over letter size it will spread to multiple pages at 100%.

                        If it is in PDF form you can open with Inkscape or GIMP and select what you...
                        Yesterday, 01:48 PM
                      • theframer
                        Reply to YoraHome Laser w/CNC Engraver/Router
                        by theframer
                        Hi Linda, great find...I think.

                        Please keep us up to date with any information you receive. I would really like to get into this, but my computer skills are almost nonexistent, I need something that a 74 year old air head 🙄 can figure out. Thanks for sharing.

                        Yesterday, 12:05 PM