Announcement

Collapse
No announcement yet.

A "different" request

Collapse
X
 
  • Time
  • Show
Clear All
new posts

  • A "different" request

    A steady customer has asked for a fretwork camel pattern, one or two hump, in the medium to advanced range. Up till now they have always asked for western themes. Any help will be appreciated as I don't remember ever seeing a fretwork camel. I'm also looking for a female figure skater pattern in the same difficulty range.

  • #2
    Here is a two humper. It will certainly be a challenge to cut. Would love to see the finished product if anyone cuts it. The pattern has a few tiny floaters in it but I dont think they will be any trouble.
    Hope this helps
    Don R
    Attached Files
    http://www.oldcrowwoodcrafts.weebly.com
    http://www.oldcrowscrollwerks.weebly.com
    Custom Made Scroll Saw Patterns

    Comment


    • #3
      Awesome pattern, this is definately what I was looking for. Hope to get started this weekend. I'll post it when finished but first it will be finding the "right" piece of wood.
      My hat is off to all who develop the patterns.
      Steve

      Comment


      • #4
        Steve, Glad you can use it.! I am working on your skater request also but it will take a little time.
        Don R
        http://www.oldcrowwoodcrafts.weebly.com
        http://www.oldcrowscrollwerks.weebly.com
        Custom Made Scroll Saw Patterns

        Comment


        • #5
          Excellent pattern Don.

          Comment


          • #6
            Steve, Here is a pattern of a skater. It is based upon this public domain photograph of Kim Yu-Na at the 2011 World Championship File:2011 WFSC 5d 343 Kim Yu-Na.JPG - Wikimedia Commons
            hope you can use it
            Don R
            Attached Files
            http://www.oldcrowwoodcrafts.weebly.com
            http://www.oldcrowscrollwerks.weebly.com
            Custom Made Scroll Saw Patterns

            Comment


            • #7
              Sweet, yep, i looked for a source image for hours, not to be found. Good job Don. Nice pattern
              russell

              Comment

              Unconfigured Ad Widget

              Collapse

              Latest Topics

              Collapse

              • will8989
                Rolf,
                by will8989
                Are you ok Rolf?
                Yesterday, 05:43 PM
              • Jim McDonald
                Reply to About ornament exchange
                by Jim McDonald
                Dave, I will participate. Thanks for doing this again.
                Yesterday, 09:10 AM
              • Rolf
                Reply to Testing this blower motor
                by Rolf
                Without the complete schematic it is hard to know what is correct.
                That said, it is a multispeed blower that obviously has a controller board. That board varies the power to the motor. By doing what you did you bypassed that. You put power across the low and high windings. If any thing connecting...
                Yesterday, 07:43 AM
              • evilbadger
                Reply to Testing this blower motor
                by evilbadger
                If he connected to red and black and the motor spun wouldn't that indicate the motor is grounded? Without connecting the white the circuit isn't complete and the motor should not spin.
                Yesterday, 06:40 AM
              • cwmagee
                Reply to Testing this blower motor
                by cwmagee
                The reason for the smoke is incorrect wiring, posible melted insulation between motor windings and motor frame.

                You mentioned connecting power to the red & and black wire. Did you do anything with White wire? Per the lable on the motor the black wire is high the Red is low. White common...
                09-28-2023, 08:41 PM
              Working...
              X
              😀
              🥰
              🤢
              😎
              😡
              👍
              👎