Portrait Pattern Help Needed.PLEASE??? - Scroll Saw Woodworking and Crafts Message Board

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

X

Steviegwood

Senior Member

Registered User - Level 2

Join Date: May 2006

Posts: 2129
- Share
- Tweet
#1

Portrait Pattern Help Needed.PLEASE???

09-23-2011, 02:57 PM

Hi Folks, I have not been around much this summer with the gardens, grass and summer chores, but I am back in scrolling mode for the fall and Christmas season. I am not that good at making portrait patterns and sure could use some of your talented help with these pics to patterns. Please & . Steve
Attached Files

harvey#1.jpg (46.0 KB, 11 views)

harvey#2.jpg (36.9 KB, 7 views)

harvey#3.jpg (65.0 KB, 9 views)

harvey#4.jpg (35.8 KB, 9 views)

If This HillBilly Can't Fix it Then it Ain't Broke!!!
My Gallery
[email protected]
Tags: None
joleet

Member - Level 2

Registered User - Level 2

Join Date: Nov 2008

Posts: 359
- Share
- Tweet
#2

09-25-2011, 12:41 PM

Steve....your pix's are not of the best quality, but I gave one of them a try. Hope it helps....Ron
Attached Files

harvey#1 copy 2.jpg (133.0 KB, 12 views)

Ron
Comment
joleet

Member - Level 2

Registered User - Level 2

Join Date: Nov 2008

Posts: 359
- Share
- Tweet
#3

09-27-2011, 10:45 AM

Steve...Here's another one....Ron
Attached Files

harvey#3 copy.jpg (120.1 KB, 7 views)

Ron
Comment
Steviegwood

Senior Member

Registered User - Level 2

Join Date: May 2006

Posts: 2129
- Share
- Tweet
#4

09-27-2011, 11:53 AM

Hi Ron, these are great. I have trouble getting people patterns right. Thanks. Steve

If This HillBilly Can't Fix it Then it Ain't Broke!!!
My Gallery
[email protected]
Comment

Previous template Next

Reply to Question about tilting head saws

by Jim Lowder

Thank you everyone. I guess I just need to scroll more and have more patience with my abilities. You all are amazing...
- Channel: Welcome Members
Yesterday, 08:08 PM
Reply to Cutting Air

by evilbadger

How thick is that foam Randy? That turned out really nice.

The view on the house is nice but that 11 foot 3 ceiling height is killing me....
- Channel: General Scroll Saw
Yesterday, 07:56 PM
Reply to Question about tilting head saws

by Rolf

I have both types of saw A tilting table Hawk g426 and an Older Excalibur with a tilting head. Unlike Carole for bevel cuts I prefer the tilting head I do larger projects and it is easier for me.
Regarding compound cuts they are cut at 90 degrees.

If I were in the market for a new...
- Channel: Welcome Members
Yesterday, 05:38 PM
Reply to Question about tilting head saws

by handibunny

If you have a good saw, and can set the table accurately, you should be good to go. Give a holler if you need help. 😁

Randy, I swapped out the clamps on the Jet for the Pegas clamps as soon as they became available. I found the Jet clamps just too fidgety for my taste.
- Channel: Welcome Members
Yesterday, 05:09 PM
Reply to Question about tilting head saws

by Jim Lowder

Thank you all for the info. Sounds like it’s talent or practice issue not my saws. Wife already gave permission to buy a new one. I will wait tho
- Channel: Welcome Members
Yesterday, 04:51 PM

Working...

X