Announcement

Collapse
No announcement yet.

another Newbie here

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • another Newbie here

    Hello to all. I am new to scroll work and also to forums so please forgive any mistakes I make. I could use a little help to learn how to get around on the forum. I have already followed a link and got a huge amount of scroll saw hints. Thanks to a Steve.


    Peggie

    Delta P-20

  • #2
    Welcome to the family. Steve
    If This HillBilly Can't Fix it Then it Ain't Broke!!!
    My Gallery
    [email protected]

    Comment


    • #3
      Welcome to our little family! There are plenty of folks here always ready to lend a helping hand, we've all been there, or on our way! So post away and visit often!
      Last edited by ozarkhillbilly; 03-22-2007, 08:05 AM.
      Bill

      DeWalt 788



      aut viam inveniam aut faciam

      God gives us only what we can handle.. Apparently God thinks I am one tough cookie.....

      Comment


      • #4
        Welcome to the club Steve.
        kevin/pitbull.

        Comment


        • #5
          Actually Steve you are the guy who put up the link I followed. Thank you again.
          Oh yes....My name is not Steve......Sorry!


          Peggie

          Delta P-20

          Comment


          • #6
            Welcome to a great group. Enjoy some playful kidding as well as excellent advice. Scrolling is a great pasttime and we all want you to succeed so ask away...
            Mike

            Craftsman 16" VS, Puros Indios and Sam Adams!
            Scrollin' since Jun/2006

            My Gallery

            http://scrollcrafters.com (reciprocal links welcomed)

            Comment


            • #7
              Welcome to the group.
              Ian

              Scrolling with a Dewalt 788

              Comment


              • #8
                Taking hints from Steve was your first mistake. lol...I'm just kidding Steve.

                Welcome fellow Canadian.
                Check me out on the web:
                http://www.kerrysworld.com

                Comment


                • #9
                  Thank you all for your replies. I do think i will enjoy it here. I have been reading other posts and am impressed at the support you give to us new people. I am sure it will take quit a while for me to get good enough to contribute in the same way. I find it daunting to be here with so many experienced artists. I have posted a picture of my first project using intarsia. I must admit i'm a little proud of how it turned out. Mind you, that is when i am not looking at the quality of work that you people do. thanks again to all of you.


                  Peggie

                  Delta P-20

                  Comment


                  • #10
                    Welcome to the fam! No need to apologize for anything. If you don't know, ask questions. If you do know, tell us. We are all learning here, helping one another. Whatever you know will help someone I'm sure.

                    Haven't seen the intarsia, where is the picture? Or did I miss another thread?
                    Troy

                    Scrollin' with DeWalt DW788

                    Comment


                    • #11
                      Welcome to our little corner of the world,They do have alot of very good info on this site.Jerry
                      Don't worry be scrolling

                      Comment


                      • #12
                        I posted the picture on the bragging page.


                        Peggie

                        Delta P-20

                        Comment

                        Unconfigured Ad Widget

                        Collapse

                        Latest Topics

                        Collapse

                        • tgiro01
                          Reply to I admit it... I splurged on a new "toy"
                          by tgiro01
                          One issue I found with the insert that comes with the saw was the areas they smoothed for the kickback pawls. If the insert is leveled correctly, those areas are sitting about 1/32-inch below the table. I had a problem with some small pieces getting caught and jamming because of that. Sawstop's recommendation...
                          Today, 08:18 AM
                        • Rolf
                          Reply to Interesting pallet
                          by Rolf
                          That is a definit rescue for a special project. I rarely get or use any pallet wood. But did use some from the pallet that my drill press was on. It looked like pine but was was very hard, carefully checked for nails and ran it through the drum sander with some 80 grit to get rid of any small grit.
                          Today, 08:16 AM
                        • Quartz43
                          Reply to Carved Fretwork Pumpkin
                          by Quartz43
                          I wish I could post the video as it looks better with the lights blinking. I used some red clear plastic behind the eyes and nose. It was a fun project.
                          Yesterday, 07:29 PM
                        • Linda In Phoenix
                          Reply to Interesting pallet
                          by Linda In Phoenix
                          Maybe a star shining to tell us something? That piece of wood is a very special piece! Good eye.
                          Yesterday, 07:27 PM
                        • Misouri Wayne
                          Reply to Bruce, the one on probation
                          by Misouri Wayne
                          Tough situation. Just have to take it one day at a time.
                          Yesterday, 04:55 PM
                        Working...
                        X