Announcement

Collapse
No announcement yet.

Yep - I'm a newbie

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Yep - I'm a newbie

    I am brand new to scroll sawing. (Which translates into - I know nothing about it). Just got a new Delta 695 20" scroll saw and in the instructions it states to "secure stand to floor before use". Is that necessary? Not to excited about putting holes into my garage floor.

  • #2
    No you don't need to secure it to the floor. You may want to add a couple of sand bags to the bottom to keep it more stable.

    Welcome A Board!! You will be hard pressed to find a friendlier or more knowledgeable group on the net re: woodworking. Share your knowledge and do not hesitate to ask questions. The only dumb question is the one that remains unasked.

    You may find the stickies at the top of this forum to be very helpful. Use the Link below.

    Message Board FAQ, Suggestions and Feedback - Scroll Saw Woodworking & Crafts Message Board.

    Take a few minutes to read through them. They are chock full of great information.

    Be sure and share pics of your projects. We thrive on pictures. You will find we are not a judgmental group.

    Whatever reason brought you to our forum we are pleased you found us.

    Take some time to read the bylaws of the forum. We do not allow open/direct selling on the forum.
    "Still Montana Mike"

    "Don't worry about old age--it doesn't last that long."
    Mike's Wood-n-Things LLC

    Comment


    • #3
      Hi Welcome to the group

      Bob
      Delta P-20 & Q-3

      I wondered why the baseball was getting bigger. Then it hit me!

      Comment


      • #4
        Welcome to the forum! I have an EX 21 mounted on a stand, but, the stand is not bolted to the floor and it is a wood floor and I have no vibration except at very high speeds, but, I cut at about 3/4 speed anyway. So no need to bolt to floor, but, as Mike said you could place sand bags or sac crete on stand frame.

        Tony,aka,Tonman from Paris, Texas

        Comment

        Unconfigured Ad Widget

        Collapse

        Latest Topics

        Collapse

        • markdavd
          Reply to Shrink wrap systems
          by markdavd
          I've been using the bags from Amazon and a heat gun my wife bought when she was a preschool teacher. Unless you are wrapping of small parts, you don't need a sealer. Just fold it over and hold it with a small piece of scotch tape on the back. After you shrink it it's sealed enough to keep everything...
          Today, 09:45 AM
        • NC Scroller
          Reply to Shrink wrap systems
          by NC Scroller
          My process is a bit different. Since I am using heat shrink bags when you seal the open end you trap a lot of air in them. When you start to heat the bag to shrink it you create a large bubble. I continue to heat the bag until it does pop a hole. I have been doing this for years. The shrink wrap...
          Today, 07:42 AM
        • will8989
          Reply to Shrink wrap systems
          by will8989
          None Linda. You need to find the right heat temp so it shrinks but doesn’t put a hole in the wrap but the tape doesn’t shrink or tear.
          Today, 12:20 AM
        • Linda In Phoenix
          Reply to Shrink wrap systems
          by Linda In Phoenix
          What thickness of film seems to work the best for puzzles?
          The bags seem easier on the surface.
          But the film seems like it is more versatile on size variations.
          Yesterday, 03:24 PM
        • will8989
          Reply to Bruce, the one on probation
          by will8989
          Regulations are 150 square feet, this will be 144 square feet so we are good. He’s making it that size Since the sheets are 4’ wide. And the Shelves need to be 4” above my head!! It will be very specific.
          Yesterday, 10:32 AM
        Working...
        X