Announcement

Collapse
No announcement yet.

New here..

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • New here..

    I am new, also. Am interested in a marble machine.


    I moved your post to it's own thread. if you piggyback in someone else's conversation your post will likely be missed.
    Last edited by wood-n-things; 06-13-2012, 03:00 PM.

  • #2
    Welcome A Board!! You will be hard pressed to find a friendlier or more knowledgeable group on the net re: woodworking. Share your knowledge and do not hesitate to ask questions. The only dumb question is the one that remains unasked.

    You may find the stickies at the top of this forum to be very helpful. Use the Link below.

    Message Board FAQ, Suggestions and Feedback - Scroll Saw Woodworking & Crafts Message Board.

    Take a few minutes to read through them. They are chock full of great information.

    Be sure and share pics of your projects. We thrive on pictures. You will find we are not a judgmental group.

    Whatever reason brought you to our forum we are pleased you found us.

    Take some time to read the bylaws of the forum. We do not allow open/direct selling on the forum.
    "Still Montana Mike"

    "Don't worry about old age--it doesn't last that long."
    Mike's Wood-n-Things LLC

    Comment


    • #3
      Steve Good has a simple one in his pattern catalog.
      May the wind at you back .....
      Not be from Lunch.

      Don't take life too seriously; No one gets out alive.

      Beauty is in the eye of the BEERHOLDER

      Visit My Gallery

      Oily's Gallery

      http://www.picturetrail.com/oily11

      Comment


      • #4
        Welcome!

        Interesting... had to google marble machine to see what it was. =) With 3 kids I think they'd love something like that.

        -brad

        Comment


        • #5
          Welcome to the forums!! Lots of great people here!!

          I'm multi-talented: I can talk and piss you off at the same time

          Comment


          • #6
            Welcome to the forum, Jim. Hope you can find all that you are interested in, here. Enjoy Scrolling & hope to see you here often.
            PERK

            Comment


            • #7
              welcome to the forum
              Someone say tool or lumber sale I am out of here

              Comment

              Unconfigured Ad Widget

              Collapse

              Latest Topics

              Collapse

              • MidMich324
                Reply to hegner 2"
                by MidMich324
                Just Wondering...

                Is the table size on the 22" hegner saw as on the 18" hegner saw?

                With the 22" inch one you get 4 more inches of depth of cut but do you also get a few more inches of table?
                Yesterday, 09:30 PM
              • will8989
                Reply to Spring Issue
                by will8989
                I had to fool around with copying and taping a pattern again today. This wasn’t as bad as the fish, but still a pain. I use rapid resizer. Scan a pattern, put in size I want and it prints it out. If more than one page, it numbers each page at the top and I tape them together. Had the fish pattern...
                Yesterday, 09:28 PM
              • millwab
                Reply to Peanuts #1
                by millwab
                Rolf, I cover it with clear contact paper (comes off clean without leaving a residue) and draw a grid for the direction I want to cut (ie horizontal or diagonal) to keep the rows even. The rest is all freehand....
                Yesterday, 02:51 PM
              • Don in Brooklin On
                Reply to Spring Issue
                by Don in Brooklin On
                Rolf

                I use acrobat reader. The poster feature will enlarge and if it goes to multiple pages it will put in cut marks. Even if the page is over letter size it will spread to multiple pages at 100%.

                If it is in PDF form you can open with Inkscape or GIMP and select what you...
                Yesterday, 01:48 PM
              • theframer
                Reply to YoraHome Laser w/CNC Engraver/Router
                by theframer
                Hi Linda, great find...I think.

                Please keep us up to date with any information you receive. I would really like to get into this, but my computer skills are almost nonexistent, I need something that a 74 year old air head 🙄 can figure out. Thanks for sharing.

                Rick
                Yesterday, 12:05 PM
              Working...
              X