Announcement

Collapse
No announcement yet.

Rookie Scrollsawer

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
  • #1

    Rookie Scrollsawer

    Hi!
    Greg from Lake Havasu City, AZ
    Just started scroll sawing and I love the craft. !!
    Tags: None
  • #2
    Welcome A Board!! You will be hard pressed to find a friendlier or more knowledgeable group on the net re: woodworking. Share your knowledge and do not hesitate to ask questions. The only dumb question is the one that remains unasked.

    You may find the stickies at the top of this forum to be very helpful. Use the Link below.

    Message Board FAQ, Suggestions and Feedback - Scroll Saw Woodworking & Crafts Message Board.

    Take a few minutes to read through them. They are chock full of great information.

    Be sure and share pics of your projects. We thrive on pictures. You will find we are not a judgmental group.

    Whatever reason brought you to our forum we are pleased you found us.

    Take some time to read the bylaws of the forum. We do not allow open/direct selling on the forum.
    "Still Montana Mike"

    "Don't worry about old age--it doesn't last that long."
    Mike's Wood-n-Things LLC

    Comment

    • #3
      welcome to the forum
      Someone say tool or lumber sale I am out of here

      Comment

      • #4
        Welcome to the forum from Beautiful Southern Oregon
        Chuck D


        When a work lifts your spirits and inspires bold and noble thoughts in you, do not look for any other standard to judge by: the work is good, the product of a master craftsman.
        Jean De La Bruyere...

        l
        Hegner 18, Delta p-20, Griz 14 inch Band saw

        Comment

        • #5
          Welcome "a-board" Greg.
          Gloria ............... Two memorable things to say in life, "Hello" for the first time, and "Good-bye" for the last.

          Comment

          Previous template Next

          Unconfigured Ad Widget

          Collapse

          Latest Topics

          Collapse
          • handibunny
            Reply to EX dust collection holes screwed up a project.!
            by handibunny
            Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
            Today, 09:21 AM
          • Bill Wilson
            Reply to EX dust collection holes screwed up a project.!
            by Bill Wilson
            I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
            Today, 09:06 AM
          • cwmagee
            Reply to EX dust collection holes screwed up a project.!
            by cwmagee
            Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
            Today, 08:40 AM
          • Rolf
            Reply to EX dust collection holes screwed up a project.!
            by Rolf
            That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
            Today, 07:28 AM
          • handibunny
            Reply to EX dust collection holes screwed up a project.!
            by handibunny
            Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
            Today, 06:21 AM
          View All
          Working...
          X