Announcement

Collapse
No announcement yet.

Hello I am new and need some help please

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Hello I am new and need some help please

    Hello so glad there is this place for questions and help. I just purchased a Rockwell RK 7315 16" Scroll saw and it states it uses these blades:
    1 x 15 TPI and 1 x 18TPI
    Can someone tell me what the [1] stands for?
    Also where would be the best place I can I purchase blades online?

    Thank you so much for allowing me to use this to get help. May God bless you all Fancy
    Last edited by wood-n-things; 01-14-2012, 01:23 PM.

  • #2
    Fancy, are they pinned or pinless blades?

    Welcome A Board!! You will be hard pressed to find a friendlier or more knowledgeable group on the net re: woodworking. Share your knowledge and do not hesitate to ask questions. The only dumb question is the one that remains unasked.

    You may find the stickies at the top of this forum to be very helpful. Use the Link below.

    Message Board FAQ, Suggestions and Feedback - Scroll Saw Woodworking & Crafts Message Board.

    Take a few minutes to read through them. They are chock full of great information.

    Be sure and share pics of your projects. We thrive on pictures. You will find we are not a judgmental group.

    Whatever reason brought you to our forum we are pleased you found us.

    Take some time to read the bylaws of the forum. We do not allow open/direct selling on the forum.
    "Still Montana Mike"

    "Don't worry about old age--it doesn't last that long."
    Mike's Wood-n-Things LLC

    Comment


    • #3
      I am not sure about blades

      I am not sure if the blades are pnned or unpinned. Because I just ordered it on line today and it will be shipped in 4 days.

      http://www.amazon.com/dp/B002CJLUYW/...SIN=B002CJLUYW

      Comment


      • #4
        I looked at the pic on amazon and it appears to take pinned blades. If it were my choice I'd cancel the order as soon as possible and get a saw designed for pinless blades. You will be sorry if you don't.
        "Still Montana Mike"

        "Don't worry about old age--it doesn't last that long."
        Mike's Wood-n-Things LLC

        Comment


        • #5
          Great reply, Mike.
          FD Mike
          SD Mike

          Comment


          • #6
            Looking at the Pic of this saw it definitly takes pinned blades and I don't see any way for it to use pinless . The 1 X 15 tpi and 1 X 18 tpi blades are what is provided with the saw. Two blades sure does not make for much cutting.

            Look for a pinless blade machine otherwise you will be turned off the fun of scrolling just because you ended up with poor equipment.

            Tom

            Comment


            • #7
              Unfortunately, nowhere in the description does it say if it takes pinned or plain end blades. Looking at the picture it looks like it takes only pinned end blades. This will limit you in many ways down the road.
              Dan in So.Ca.

              Comment


              • #8
                Fancy, Take Mikes advice and cancel the order. You could get this one http://www.amazon.com/Craftsman-Vari...517028&sr=1-12 from Amazon.com for $50 more.
                I bought a Craftsman 18 inch variable speed 5 or 6 years ago and am still using it. Some people on this board don't recommend Craftsman saws but in my experience they are good value for the money. Most of my cutting is in wood 1.5 to 2 inches thick and the Craftsman does a great job.
                Good luck
                Don R
                http://www.oldcrowwoodcrafts.weebly.com
                http://www.oldcrowscrollwerks.weebly.com
                Custom Made Scroll Saw Patterns

                Comment


                • #9
                  That saw looks like exactly like the Ryobi saw I used to have. It was able to use pinless blades but was very aggravating because they always slipped out when you tried to get it tension-ed properly. While the saw I had was able to use pinless blades and this looks identical I am not saying the saw you ordered will take pinless blades. For what it's worth I will say that I almost gave up scrolling early on because of that saw. Good luck and you've certainly found the right place to learn and share about scrolling.
                  Don

                  An investment in knowledge pays the best interest.
                  Benjamin Franklin

                  At twenty years of age the will reigns; at thirty, the wit; and at forty, the judgment.
                  Benjamin Franklin

                  A great empire, like a great cake, is most easily diminished at the edges.
                  Benjamin Franklin

                  www.dogwoodstudiosnh.com

                  Comment


                  • #10
                    fancy, I would have to aggree with canceling your order if you can. You will not enjoy scrolling if you can't cut the patterns. I mean that you would not be able to insert the pinned blade in a drilled hole. Most patterns call for small blade insertion. Hope you can achieve what you want with scrolling. Good Luck
                    PERK

                    Comment


                    • #11
                      Can you tell me what the [1] means

                      Can you tell me what the .....................1 x 15 TPI and 1 x 18TPI
                      stands for?
                      Hope to hear from from you soon God Bless, Fancy


                      Not polite to shout all caps and bolding is considered shouting... I edited your post..
                      Last edited by wood-n-things; 01-14-2012, 01:20 PM.

                      Comment


                      • #12
                        Well, What that says is 1 inch by 15 teeth per inch or 18 teeth per inch, but that has to be incorrect because there is no such thing a a one inch blade! 99.9% of blades sold are 5".
                        Dan in So.Ca.

                        Comment


                        • #13
                          So did you take our advice and cancel this saw and order a different saw that takes pinless blades?
                          "Still Montana Mike"

                          "Don't worry about old age--it doesn't last that long."
                          Mike's Wood-n-Things LLC

                          Comment


                          • #14
                            I believe that the 1 stands for one blade which means that you are getting two blades. One of them has 15 teeth per inch and the other has 18 teeth per inch.
                            If you are going to buy blades I suggest you contact Mike at Mikes Workshop Mike's Workshop English featuring: my life story, a cancer survivor, scrollsawing samples and tips, community service, list of favorite sites and Flying Dutchman fretsaw blades for sale.
                            Don R
                            http://www.oldcrowwoodcrafts.weebly.com
                            http://www.oldcrowscrollwerks.weebly.com
                            Custom Made Scroll Saw Patterns

                            Comment


                            • #15
                              Your probably right about the number of blades Don. In normal woodworking measures, It would suggest 1" x 15 or 18 tpi. They are defiantly pinned end blades and mike does not sell them.
                              Something else that does not make sense, I was looking at the specs on Amazon. It list the weight of the saw at 53 pounds and the shipping weight at 29.8 pounds! Is that crazy or am I missing something?
                              Dan in So.Ca.

                              Comment

                              Unconfigured Ad Widget

                              Collapse

                              Latest Topics

                              Collapse

                              • KarlB
                                Reply to Shawl pins
                                by KarlB
                                That's what I was wondering Betty: If these would work (larger) for hair?

                                Karl...
                                Today, 04:47 PM
                              • RJweb
                                Reply to Shawl pins
                                by RJweb
                                Who said being bald isn’t a plus, RJ...
                                Today, 01:18 PM
                              • will8989
                                Reply to EX dust collection holes screwed up a project.!
                                by will8989
                                The perfect solution when I need a wider top on my Hegner. A magnetic sheet! I decided not to get the Pegas as the only reason was for the wider top and the top feed blade. After 19 years, my Hegner is still running like new and I couldn’t justify the expense. It was a “want” and not a “need”....
                                Today, 12:27 PM
                              • will8989
                                Reply to Shawl pins
                                by will8989
                                Good idea Scott. Also, my daughter has long, curly hair. She twists it up and around and sticks a pencil in to hold it. I also stick a dowel in my hair when working and my hair gets in my way and I twist it up. The one in this picture would perfect for thick hair.
                                Today, 12:19 PM
                              • NC Scroller
                                Reply to Shawl pins
                                by NC Scroller
                                Very Interesting. Axor being this is a vary old thread you might reach more people by starting a new thread for your video....
                                Today, 08:56 AM
                              Working...
                              X