Announcement

Collapse
No announcement yet.

Newbie from Mesquite Texas!!!

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
  • #1

    Newbie from Mesquite Texas!!!

    Just joined up and wanted to say hey to everyone out there. Just looking this seems to be a pretty good place to hang out.
    Tags: None
  • #2
    achennau, If you like playing with wood, your in the right place.And we like pictures. Welcome,Lance

    Comment

    • #3
      You will like it here. The folks are so friendly and helpful...someone always answers my questions.
      I have a bandsaw, so I'm not new to woodcrafting.....I had an el-cheapo scrollsaw once from sears....it didn't last til the water got hot.
      I am going to purchase an excalibur 16" pretty soon.
      I had my workshop updated so it could be heated and cooled.


      Originally posted by achennau View Post
      Just joined up and wanted to say hey to everyone out there. Just looking this seems to be a pretty good place to hang out.

      Comment

      • #4
        Glad you joined up, achennau. I be your neighbor on the Balch Springs Dallas lines.
        Anxious to see some of the things you make.
        Fran

        Comment

        • #5
          Welcome from Lubbock
          Hegner Polymax- 3,Hegner Multimax-3,
          "No PHD, just a DD 214"

          Comment

          • #6
            Hi from Garland...All kinds of great info here.

            EX-16

            Comment

            • #7
              Welcome A Board!! You will be hard pressed to find a friendlier or more knowledgeable group on the net re: woodworking. Share your knowledge and do not hesitate to ask questions.

              You may find the stickies at the top of this forum to be very helpful. Use the Link below.

              Message Board FAQ, Suggestions and Feedback - Scroll Saw Woodworking & Crafts Message Board.

              Take a few minutes to read through them. They are chock full of great information.

              Be sure and share pics of your projects. We thrive on pictures.

              The only dumb question is the one that remains unasked.

              Whatever reason brought you to our forum we are pleased you found us.

              Take some time to read the bylaws of the forum. We do not allow open/direct selling on the forum.
              "Still Montana Mike"

              "Don't worry about old age--it doesn't last that long."
              Mike's Wood-n-Things LLC

              Comment

              Previous template Next

              Unconfigured Ad Widget

              Collapse

              Latest Topics

              Collapse
              • handibunny
                Reply to EX dust collection holes screwed up a project.!
                by handibunny
                Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
                Today, 09:21 AM
              • Bill Wilson
                Reply to EX dust collection holes screwed up a project.!
                by Bill Wilson
                I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
                Today, 09:06 AM
              • cwmagee
                Reply to EX dust collection holes screwed up a project.!
                by cwmagee
                Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
                Today, 08:40 AM
              • Rolf
                Reply to EX dust collection holes screwed up a project.!
                by Rolf
                That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
                Today, 07:28 AM
              • handibunny
                Reply to EX dust collection holes screwed up a project.!
                by handibunny
                Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
                Today, 06:21 AM
              View All
              Working...
              X