Announcement

Collapse
No announcement yet.

Hi Everyone

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Hi Everyone

    I am a new beginner I made my first piece a small cross for my God child to hang from her mirror in her car. She was so excited. So now on to making some more for christmas presents. I am looking forward to becoming a part of this community as I am sure to gather alot of knowledge and insight from everyone on my new scrollsawer journey Thanks!!!!!

  • #2
    Hi Linda, welcome to the group.

    Bob
    Delta P-20 & Q-3

    I wondered why the baseball was getting bigger. Then it hit me!

    Comment


    • #3
      Welcome A Board!! You will be hard pressed to find a friendlier or more knowledgeable group on the net re: woodworking. Share your knowledge and do not hesitate to ask questions.

      You may find the stickies at the top of this forum to be very helpful. Use the Link below.

      Message Board FAQ, Suggestions and Feedback - Scroll Saw Woodworking & Crafts Message Board.

      Take a few minutes to read through them. They are chock full of great information.

      Be sure and share pics of your projects. We thrive on pictures.

      The only dumb question is the one that remains unasked.

      Whatever reason brought you to our forum we are pleased you found us.

      Take some time to read the bylaws of the forum. We do not allow open/direct selling on the forum.
      "Still Montana Mike"

      "Don't worry about old age--it doesn't last that long."
      Mike's Wood-n-Things LLC

      Comment


      • #4
        Linda, welcome to our friendly group as we are here to help you. feel free to pick our brains and to contribute your ideas and thoughts.

        Mike from California

        Comment


        • #5
          welcome to the group.we are glad you joined
          Tricia

          Comment


          • #6
            Hi Linda - we're glad to have you here! How cool that your first piece was a gift -- doesn't that just make you feel terrific?! We'd love to see pictures as you make more of them!

            Comment


            • #7
              Welcome "a-board" Linda, come by often, lots of information here, and feel free to dispense some of your info with us too. Oh and by the way, we love project photos, so don't be shy, not mandatory to post your photos, but sure appreciated. Gives food for thought.
              Gloria ............... Two memorable things to say in life, "Hello" for the first time, and "Good-bye" for the last.

              Comment

              Unconfigured Ad Widget

              Collapse

              Latest Topics

              Collapse

              • handibunny
                Reply to EX dust collection holes screwed up a project.!
                by handibunny
                Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
                Today, 09:21 AM
              • Bill Wilson
                Reply to EX dust collection holes screwed up a project.!
                by Bill Wilson
                I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
                Today, 09:06 AM
              • cwmagee
                Reply to EX dust collection holes screwed up a project.!
                by cwmagee
                Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
                Today, 08:40 AM
              • Rolf
                Reply to EX dust collection holes screwed up a project.!
                by Rolf
                That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
                Today, 07:28 AM
              • handibunny
                Reply to EX dust collection holes screwed up a project.!
                by handibunny
                Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
                Today, 06:21 AM
              Working...
              X