No announcement yet.

Hi All!

  • Filter
  • Time
  • Show
Clear All
new posts

  • Hi All!

    Been scrolling with an old C-type saw for about 6 years and just recently bought an Excalibur. Wow what a difference. I will post a few things I have done in the near future. Really like the site here and hope to contribute as much as possible.


  • #2

    Here's a cut from an old Creative Woodworks & Crafts pattern from a few years back. This was done with the old jap C-type saw.

    Attached Files


    • #3
      Hi again...

      And here my latest of my brother done on the new Excalibur.
      Hope you like.

      Attached Files


      • #4
        I think I put these pics in the wrong place,,,sorry bout that.


        • #5
          Welcome Coullion. Good cutting shown already. Keep up the good work.


          • #6
            Welcome A Board!! You will be hard pressed to find a friendlier or more knowledgeable group on the net re: woodworking. Share your knowledge and do not hesitate to ask questions.

            You may find the stickies at the top of this forum to be very helpful. Use the Link below.

            Message Board FAQ, Suggestions and Feedback - Scroll Saw Woodworking & Crafts Message Board.

            Take a few minutes to read through them. They are chock full of great information.

            Be sure and share pics of your projects. We thrive on pictures.

            The only dumb question is the one that remains unasked.

            Whatever reason brought you to our forum we are pleased you found us.

            Take some time to read the bylaws of the forum. We do not allow open/direct selling on the forum.
            "Still Montana Mike"

            "Don't worry about old age--it doesn't last that long."
            Mike's Wood-n-Things LLC


            • #7
              Welcome Copullion, sweeeeet cut on that portrait.
              Gloria ............... Two memorable things to say in life, "Hello" for the first time, and "Good-bye" for the last.


              • #8
                welcome, you did a great job, keep up the good work


                • #9
                  Todd, the pieces are terrific! I continue to be amazed at how the portraits turn out == I think I would recognize your brother from the photograph if I saw him on the street! Am I seeing that the earlier piece is inlay?


                  • #10
                    No...not inlay...just a dark background. Thanks for the words of encouragement.



                    Unconfigured Ad Widget


                    Latest Topics


                    • Tom in Ashland
                      Fiona Kingdon pattern from Summer issue
                      by Tom in Ashland
                      Quarter inch BB with Red Gum (Australian Eucalyptus) veneer. My first attempt at veneering and there are a couple spots where there was not quit enough glue so small pieces of the veneer came off....
                      Today, 07:59 PM
                    • millwab
                      Cutting Styles
                      by millwab
                      In preparation for a scrolling demonstration I decided to make up a piece that would show the different ways I've cut puzzles. It's 2 layers of 1/8" BB. The puzzles were cut out as tray puzzles and then glued back in so pieces wouldn't get lost as it was handled.
                      Today, 04:41 PM
                    • jim_mex
                      Reply to Workshop extension and major facelift - a work in progress - update at 13 April
                      by jim_mex
                      Update at 13 AprilIts been almost a month since my last post and my shop extension is progressing albeit slowly largely due to me nibbling at it on a regular basis rather than sticking with it and going full blast to get it finished.

                      The outside
                      of the extension is almost finished apart...
                      Today, 03:45 PM
                    • Rolf
                      Reply to New Toy!
                      by Rolf
                      Quartz I only bought the air filter, That same model is sold by many distributors, I see Grizzly has it and several others. I was going to build one but this thing works great. I will get a charcoal filter for it also. Great when doing Pyrography. They also had a Pfingst brand flex shaft tool I haven't...
                      Today, 07:50 AM
                    • NC Scroller
                      Reply to New Toy!
                      by NC Scroller
                      Nice score!
                      Today, 06:16 AM