Announcement

Collapse
No announcement yet.

New Member

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
  • #1

    New Member

    Hello to all the members here. I am Fretnot. I am new to scroll sawing so still have a lot of learning to do. I have a pre used DeWalt 788 and will shortly be getting an Excalibur 21. I have really got the scroll saw bug bad and just setting up a separate workshop just for scroll sawing. I also do wood turning and everything I make I sell to craft centres and also sell at craft fairs. So far it is going very well. I am keen to learn all about intarsia but will wait until I have some experience under my belt as it looks hard and complicated. I hope so show some pieces on here soon.
    Tags: None
  • #2
    Welcome A Board!! You will be hard pressed to find a friendlier or more knowledgeable group on the net re: woodworking. Share your knowledge and do not hesitate to ask questions.

    You may find the stickies at the top of this forum to be very helpful. Use the Link below.

    Message Board FAQ, Suggestions and Feedback - Scroll Saw Woodworking & Crafts Message Board.

    Take a few minutes to read through them. They are chock full of great information.

    Be sure and share pics of your projects. We thrive on pictures.

    The only dumb question is the one that remains unasked.

    Whatever reason brought you to our forum we are pleased you found us.
    "Still Montana Mike"

    "Don't worry about old age--it doesn't last that long."
    Mike's Wood-n-Things LLC

    Comment

    • #3
      Welcome fretnot, we always like pics.
      Rose

      Comment

      • #4
        Welcome.
        As Rose said. We like to see photos of your work.
        Pacifism is great, as long as everyone is participating.


        StephenD


        The Southern Arizona Woodturners Association
        Desert Woodcrafters
        Grandpa for the 7 most amazing children.

        Comment

        • #5
          Welcome. There is many very talented intarsia people on this forum. Pictures are great.

          Comment

          • #6
            welcome aboard
            Tricia

            Comment

            Previous template Next

            Unconfigured Ad Widget

            Collapse

            Latest Topics

            Collapse
            • NC Scroller
              Reply to Shrink wrap systems
              by NC Scroller
              My process is a bit different. Since I am using heat shrink bags when you seal the open end you trap a lot of air in them. When you start to heat the bag to shrink it you create a large bubble. I continue to heat the bag until it does pop a hole. I have been doing this for years. The shrink wrap...
              Today, 07:42 AM
            • will8989
              Reply to Shrink wrap systems
              by will8989
              None Linda. You need to find the right heat temp so it shrinks but doesn’t put a hole in the wrap but the tape doesn’t shrink or tear.
              Today, 12:20 AM
            • Linda In Phoenix
              Reply to Shrink wrap systems
              by Linda In Phoenix
              What thickness of film seems to work the best for puzzles?
              The bags seem easier on the surface.
              But the film seems like it is more versatile on size variations.
              Yesterday, 03:24 PM
            • will8989
              Reply to Bruce, the one on probation
              by will8989
              Regulations are 150 square feet, this will be 144 square feet so we are good. He’s making it that size Since the sheets are 4’ wide. And the Shelves need to be 4” above my head!! It will be very specific.
              Yesterday, 10:32 AM
            • Sandy Oaks
              Reply to Shrink wrap systems
              by Sandy Oaks
              As a framer, we have a shrinker wrapper at ArtCrafters. Very simple. Film on a roller, sealer attached, just roll off enough film, seal the film, insert object, seal other end and shrink with a heat gum. We also use Uline as a source. Not sure where our unit can from as it was with the shop when...
              Yesterday, 09:46 AM
            View All
            Working...
            X