Announcement

Collapse
No announcement yet.

Regarding Scroller tips

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Regarding Scroller tips

    We thank the staff for the page in the magazine regarding tips and tricks for new scrollers.

    I DO have one addition/suggestion/opinion to add to squaring the table.

    You talk about making sure the blade is square to the table (left and right) and that it is imperative during stack cutting. What you do NOT talk about is that is is also imperative to have the blade square front to back for stack cutting. To make acurate cuts over several layers, the blade should be square 365 degrees. This also very much comes into play when cutting 3/4" material.

    There - that's my 2% of a dollar.
    Fred
    aka Pop's Shop
    Life isn't about waiting for the storm to pass...it's about learning to dance in the rain!.

  • #2
    I think this is a moot point. I don't know of any scroll saw where you can adjust the table (front and back) to the blade. There is only one proper way to put the blade into the upper and lower clamps which is to seat it all the way to the rear. Also with saws like the Dewalt and other cheaper ones, the excessive front to back blade motion messes that up anyway. Having the blade square to the table front to back has everything to do with the design of the saw and not any kind of adjustment you can make on your own.

    Comment


    • #3
      Actually the Hawk G4 does have an adjustment for just that. You can move the lower blade clamp front to back with an allen wrench.
      Rolf
      RBI G4 26 Hawk, EX 16 with Pegas clamps, Nova 1624 DVR XP
      Philosophy "I don't know that I can't, therefore I can"
      Proud Member of the Long Island Woodworkers Club
      And the Long Island Scrollsaw Association

      Comment


      • #4
        Oh wow I never heard of a saw with that capability. I know the dewalt and the EX dont have them. Even if you can make that adjustment on that saw, I wonder how you go about making sure it's square when almost all saws have some front to back blade motion?

        Comment


        • #5
          When I took my sweet old DW788, to the Dw Service Center, they replaced my worn out machine with a new one. The blade was way out of square front to back. I removed the bolt from the rear table support, then began raising the support, and table, using a tapered wood wedge until it was square. The result was I could drill a new bolt hole adove the old. The solution worked well, for me.O
          Manufacturer Of Heirloom Quality Sawdust

          I wasn't born in the south, but I got here as fast as I could!

          Dewalt DW788 Hegner Maximat 18

          Comment


          • #6
            But when the blade isn't traveling perfectly up and down and has excessive front to back motion, even if you can square the table front to back, how do you do it when you have to compensate for the blade motion?

            Comment


            • #7
              I don't understand what you mean by square 365 degrees? A year has 365 days but a circle has 360 degrees. But the blade should be at 90 degrees to the table. Hardrock

              Comment


              • #8
                What he meant was square left and right and also front and back.

                Comment

                Unconfigured Ad Widget

                Collapse

                Latest Topics

                Collapse

                • will8989
                  Reply to Farmers market
                  by will8989
                  I just used different wood scraps I had to make the kayaks. I still do t see anymore in my future.
                  Today, 01:09 AM
                • Jim McDonald
                  Reply to Delta Q3 fuse question
                  by Jim McDonald
                  Twenty years in electronics retail and here is a quick dirty way to tell the difference:
                  a fast blow will only have the wire element. Slow blow almost always has some extra structure that will be left behind after the fuse blows.
                  Secondly, there is a series of three letter engraved on one...
                  Yesterday, 08:54 PM
                • Ennobee
                  Reply to Looking For Mom and Baby Animal Pattern
                  by Ennobee
                  They look like David Spielmann's Designs to me. I will check my library this evening, but I bet you already that they are from one of his pattern books.
                  Yesterday, 01:55 PM
                • jim_mex
                  Reply to My first decent furniture project - Welding and woodwork combined
                  by jim_mex
                  Thanks all - you folks do wonders for my ego with your comments and importantly fire me up to keep trying new things

                  Scott - once this Covid situation has passed I'll definitely be heading up to NC. I'm tentatively thinking late spring/early summer next year. I am not sure just what pointers...
                  Yesterday, 01:35 PM
                • JustLarry
                  Reply to Delta Q3 fuse question
                  by JustLarry
                  I found this information on fuses in general.

                  Blowing type. Fast-blow fuses will blow as soon as the current reaches the fuse's amperage rating, while slow-blow fuses are designed to tolerate a large number of startup surges and modest short-term overloads without blowing.
                  Fast-blow...
                  Yesterday, 12:56 PM
                Working...
                X