Announcement

Collapse
No announcement yet.

Online ticket Problem.

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Online ticket Problem.

    I am having a problem purchasing the tickets online?
    This is the message I get.


    The error occurred in D:\Web_Root\foxchapel\basket\addtocartSKU.cfm: line 69

    67 : </cfif>
    68 :
    69 : <cfif len(SKUorISBN) gt 6 >
    70 : <cfset lastcharX = right(#SKUorISBN#,1) >
    71 : <cfset SKUorISBN = rereplace(#SKUorISBN#,"[A-Za-z]","","ALL") >
    Rolf
    RBI G4 26 Hawk, EX 16 with Pegas clamps, Nova 1624 DVR XP
    Philosophy "I don't know that I can't, therefore I can"
    Proud Member of the Long Island Woodworkers Club
    And the Long Island Scrollsaw Association

  • #2
    You're not the only one, Rolf. I've asked Rob (Admin) to check into it!

    You may want to call in to our customer service department...
    1-800-457-9112

    Bob
    www.GrobetUSA.com

    Comment


    • #3
      Bob,

      The problem seems to be resolved. I managed to register online this morning.

      Thanks
      Rolf
      RBI G4 26 Hawk, EX 16 with Pegas clamps, Nova 1624 DVR XP
      Philosophy "I don't know that I can't, therefore I can"
      Proud Member of the Long Island Woodworkers Club
      And the Long Island Scrollsaw Association

      Comment


      • #4
        Just got an e-mail from Rob...confirming that it's fixed...

        Thanks!

        Bob
        www.GrobetUSA.com

        Comment

        Unconfigured Ad Widget

        Collapse

        Latest Topics

        Collapse

        • handibunny
          Reply to EX dust collection holes screwed up a project.!
          by handibunny
          Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
          Today, 09:21 AM
        • Bill Wilson
          Reply to EX dust collection holes screwed up a project.!
          by Bill Wilson
          I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
          Today, 09:06 AM
        • cwmagee
          Reply to EX dust collection holes screwed up a project.!
          by cwmagee
          Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
          Today, 08:40 AM
        • Rolf
          Reply to EX dust collection holes screwed up a project.!
          by Rolf
          That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
          Today, 07:28 AM
        • handibunny
          Reply to EX dust collection holes screwed up a project.!
          by handibunny
          Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
          Today, 06:21 AM
        Working...
        X