Announcement

Collapse
No announcement yet.

Minnesota scroller

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Minnesota scroller

    Sorry i have been mistreating my scrolling friends by not stopping in and making them listen to my redredic

    I been a good boy taking all my meds and reconstructing this hobble were buying 2 rooms with Sheetrock replacement reinsulation and revamping a 100 year old house, means repairing termite and fungal damage so any 3 day project runs on and on...

    the meds make me stupid with a drunkards attitude and absolutely no concentration, since carving takes hardly any forethought my spare time is spent on the porch spitting and whittling then sweeping up chips, as i cant keep my mind on the project with a scroll saw,

    I know there are lots of great projects being discussed daily here but i dont have the faciltys to keep up.

    but i been using my saws to cut out or roughly removing scrap from basswood stock for carving projects so im keeping the saws running...

    ill honestly make effort to stop in more often if i dont holler at me bobd made me a moderator on the carving forums cuz i wouldn't keep my mouth-fingers still...

    thanks for understanding
    Thomas
    Last edited by Thomp; 03-02-2007, 11:18 PM.
    Dremel 1680 & Delta ss250 shopmaster

  • #2
    Nice to see your smilin face again Thom.
    Take care of yourself and I will visit you on WCI
    CAЯL HIRD-RUTTEЯ
    "proud member of the best scroll sawing forum on the net."
    Ryobi SC180VS scroll saw EX21

    Comment


    • #3
      I wish you good health Thomas,

      Take care of yourself, and watch those sharp knife blades.

      Regards,
      Marcel
      http://marleb.com
      DW788. -Have fun in the shop or it isn't a hobby anymore.

      NOTE: No trees were killed in the sending of this message, but a large number of electrons were terribly inconvenienced.

      Comment


      • #4
        Take care of yourself Thom.

        Bob
        Delta P-20 & Q-3

        I wondered why the baseball was getting bigger. Then it hit me!

        Comment

        Unconfigured Ad Widget

        Collapse

        Latest Topics

        Collapse

        • MidMich324
          Reply to hegner 2"
          by MidMich324
          Just Wondering...

          Is the table size on the 22" hegner saw as on the 18" hegner saw?

          With the 22" inch one you get 4 more inches of depth of cut but do you also get a few more inches of table?
          Yesterday, 09:30 PM
        • will8989
          Reply to Spring Issue
          by will8989
          I had to fool around with copying and taping a pattern again today. This wasn’t as bad as the fish, but still a pain. I use rapid resizer. Scan a pattern, put in size I want and it prints it out. If more than one page, it numbers each page at the top and I tape them together. Had the fish pattern...
          Yesterday, 09:28 PM
        • millwab
          Reply to Peanuts #1
          by millwab
          Rolf, I cover it with clear contact paper (comes off clean without leaving a residue) and draw a grid for the direction I want to cut (ie horizontal or diagonal) to keep the rows even. The rest is all freehand....
          Yesterday, 02:51 PM
        • Don in Brooklin On
          Reply to Spring Issue
          by Don in Brooklin On
          Rolf

          I use acrobat reader. The poster feature will enlarge and if it goes to multiple pages it will put in cut marks. Even if the page is over letter size it will spread to multiple pages at 100%.

          If it is in PDF form you can open with Inkscape or GIMP and select what you...
          Yesterday, 01:48 PM
        • theframer
          Reply to YoraHome Laser w/CNC Engraver/Router
          by theframer
          Hi Linda, great find...I think.

          Please keep us up to date with any information you receive. I would really like to get into this, but my computer skills are almost nonexistent, I need something that a 74 year old air head 🙄 can figure out. Thanks for sharing.

          Rick
          Yesterday, 12:05 PM
        Working...
        X