Announcement

Collapse
No announcement yet.

Canadianscroller

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Canadianscroller

    To read a bit about Carl and see him ballroom dancing, go here
    Sue Mey
    Website: www.scrollsawartist.com

  • #2
    well i never, you certainly learn something new every day on this forum. lol. good for you carl aka twinkle-toes. lol

    kevin
    kevin/pitbull.

    Comment


    • #3
      Carl deserves a nice tribute like that!

      Gill
      There is no opinion, however absurd, which men will not readily embrace as soon as they can be brought to the conviction that it is readily adopted.
      (Schopenhauer, Die Kunst Recht zu Behalten)

      Comment


      • #4
        Hey Carl's fame is spreading internationally ... bit disappointed though, Sue, I thought there was going to be a video ...
        Ian

        Scrolling with a Dewalt 788

        Comment


        • #5
          Sorry, no video...maybe next time
          Sue Mey
          Website: www.scrollsawartist.com

          Comment


          • #6
            CAЯL HIRD-RUTTEЯ
            "proud member of the best scroll sawing forum on the net."
            Ryobi SC180VS scroll saw EX21

            Comment


            • #7
              Carl, is that your twin. What a resemblance. haha Steve
              If This HillBilly Can't Fix it Then it Ain't Broke!!!
              My Gallery
              [email protected]

              Comment


              • #8
                hey carl! What blade did you use to scroll that?
                kevin/pitbull.

                Comment


                • #9
                  Being round, is there a chance it was spirals? Steve
                  If This HillBilly Can't Fix it Then it Ain't Broke!!!
                  My Gallery
                  [email protected]

                  Comment


                  • #10
                    Being a dancer myself I am impressed with your abilities Carl.
                    Dragon
                    Owner of a nice 21" Excalibur
                    Owner of a Dewalt 788
                    PuffityDragon on AFSP

                    Comment

                    Unconfigured Ad Widget

                    Collapse

                    Latest Topics

                    Collapse

                    • handibunny
                      Reply to EX dust collection holes screwed up a project.!
                      by handibunny
                      Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
                      Today, 09:21 AM
                    • Bill Wilson
                      Reply to EX dust collection holes screwed up a project.!
                      by Bill Wilson
                      I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
                      Today, 09:06 AM
                    • cwmagee
                      Reply to EX dust collection holes screwed up a project.!
                      by cwmagee
                      Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
                      Today, 08:40 AM
                    • Rolf
                      Reply to EX dust collection holes screwed up a project.!
                      by Rolf
                      That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
                      Today, 07:28 AM
                    • handibunny
                      Reply to EX dust collection holes screwed up a project.!
                      by handibunny
                      Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
                      Today, 06:21 AM
                    Working...
                    X