Announcement

Collapse
No announcement yet.

Steve Ramsey strikes again AAAAAAAAAAAAAAAA

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
  • #1

    Steve Ramsey strikes again AAAAAAAAAAAAAAAA

    If you are like me, and I know I am, you get a kick out of Steve Ramsey's videos.

    A woodworking Christmas, from Steve and Alex. - YouTube
    Pacifism is great, as long as everyone is participating.


    StephenD


    The Southern Arizona Woodturners Association
    Desert Woodcrafters
    Grandpa for the 7 most amazing children.
    Tags: None
  • #2
    That was a hoot. I subscribe to his newsletter. Look forward to it all the time.
    "Still Montana Mike"

    "Don't worry about old age--it doesn't last that long."
    Mike's Wood-n-Things LLC

    Comment

    • #3
      Thanks Stephen - enjoyed these nuts ...............MB
      Usually busier than a cat in a sandbox !!!!!!!!!!! MB { Dewalt 788 only }

      Comment

      • #4
        Aye, have watched a few of his vids, very funny man I have enjoyed the few I have watched. Should subscribe realy.
        The Journey Is Everything.

        http://www.sunlion-pyrography.co.uk/

        My Google+

        Comment

        • #5
          That was crazy and very good. Enjoyed..
          Chuck D


          When a work lifts your spirits and inspires bold and noble thoughts in you, do not look for any other standard to judge by: the work is good, the product of a master craftsman.
          Jean De La Bruyere...

          l
          Hegner 18, Delta p-20, Griz 14 inch Band saw

          Comment

          • #6
            Nice video Stephen - although I'm not sure I could listen to that twice! That sounds worse than even my lame attempts at singing in tune. Very funny though and Steven Ramsey is a really helpful guy.
            Jim in Mexico

            Logic will get you from A to B. Imagination will take you everywhere.
            - Albert Einstein

            Comment

            • #7
              Stephen, that is just off the wall. Thanks for sharing it with us.

              george
              A day without sawdust is a day without sunshine.
              George

              delta 650, hawk G426

              Comment

              Previous template Next

              Unconfigured Ad Widget

              Collapse

              Latest Topics

              Collapse
              • handibunny
                Reply to EX dust collection holes screwed up a project.!
                by handibunny
                Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
                Today, 09:21 AM
              • Bill Wilson
                Reply to EX dust collection holes screwed up a project.!
                by Bill Wilson
                I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
                Today, 09:06 AM
              • cwmagee
                Reply to EX dust collection holes screwed up a project.!
                by cwmagee
                Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
                Today, 08:40 AM
              • Rolf
                Reply to EX dust collection holes screwed up a project.!
                by Rolf
                That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
                Today, 07:28 AM
              • handibunny
                Reply to EX dust collection holes screwed up a project.!
                by handibunny
                Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
                Today, 06:21 AM
              View All
              Working...
              X