Announcement

Collapse
No announcement yet.

Top o the Mornin to ya

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Top o the Mornin to ya

    Happy St. Patties day for all you green wearing people.

    I am not Irish but it is a big day in our house, my daughters birthday, I think we are going out for green drinks tonight, whatever that means.

    A few years ago she had Patty O'Green tattooed on her shoulder

    Not this exact image but close.
    CAЯL HIRD-RUTTEЯ
    "proud member of the best scroll sawing forum on the net."
    Ryobi SC180VS scroll saw EX21

  • #2
    Carl - give her a big ole warm hug from me for her B DAY. and be careful on the green drinks they make you see green elephants. lol
    Sharon

    Comment


    • #3
      Green drinks

      Carl...first let me wish your daughter a very happy birthday!!! Now I have two things to celebrate today. I forgot it's St. Paddy's day so now I have a good reason to go have a couple and shoot a little pool with the guys.
      If it don't fit, don't force it....get a bigger hammer!!

      Comment


      • #4
        St Patrick's Day was yesterday for us folks. We all done the green hair bit at the school where I work. Great fun! Thank goodness there's no photos!
        Cheers. Teresa .

        Comment


        • #5
          Tell her Happy Birthday!!!
          It's my 27th Wedding Anniversary also! Turns out to be a Great Day!

          Best of Wishes!
          Tim
          "All it Takes For the Forces of EVIL to Rule Is For Enough GOOD People To DO NOTHING!"

          Saws: Excaliber 30; Dewalt 788 'Twins', Makita SJ401 (Retired), Grizzly G1012 18" Bandsaw

          Comment

          Unconfigured Ad Widget

          Collapse

          Latest Topics

          Collapse

          • handibunny
            Reply to EX dust collection holes screwed up a project.!
            by handibunny
            Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
            Today, 09:21 AM
          • Bill Wilson
            Reply to EX dust collection holes screwed up a project.!
            by Bill Wilson
            I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
            Today, 09:06 AM
          • cwmagee
            Reply to EX dust collection holes screwed up a project.!
            by cwmagee
            Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
            Today, 08:40 AM
          • Rolf
            Reply to EX dust collection holes screwed up a project.!
            by Rolf
            That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
            Today, 07:28 AM
          • handibunny
            Reply to EX dust collection holes screwed up a project.!
            by handibunny
            Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
            Today, 06:21 AM
          Working...
          X