Announcement

Collapse
No announcement yet.

Mt Augustine erupting

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
  • #1

    Mt Augustine erupting

    Wth all the talk about record rain and record drought, thought I'd share the excitement from the last frontier........ a volcano erupting less than 200 miles south of Anchorage. It's went off 4 time so far today, no ash in the big city as the winds are keeping it away. For more info than you could ever want, go to:

    http://www.avo.alaska.edu/

    The Augustine images page takes awhile to load, but has lots of really cool photo's. While not Mt St Helens or Krakatoa in scope, it is still pretty interesting.
    ‎"Orphans are easier to ignore before you know their names. They're easier to ignore before you see their faces. It's easier to pretend they're not real before you hold them in your arms. But once you do, everything changes."

    D. Platt
    Tags: None
  • #2
    Thats HOT news!
    makes a little rain seem dreary.
    CAЯL HIRD-RUTTEЯ
    "proud member of the best scroll sawing forum on the net."
    Ryobi SC180VS scroll saw EX21

    Comment

    • #3
      I've been reading that in the newspapers my folks send me. I remember back around 89'-90' when one of them volcanos went off, made a big mess of things with all the ash.
      Todd

      Hawk G4, Dremel 1800

      Quando Omni Flunkus Moritati

      Comment

      Previous template Next

      Unconfigured Ad Widget

      Collapse

      Latest Topics

      Collapse
      • handibunny
        Reply to EX dust collection holes screwed up a project.!
        by handibunny
        Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
        Today, 09:21 AM
      • Bill Wilson
        Reply to EX dust collection holes screwed up a project.!
        by Bill Wilson
        I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
        Today, 09:06 AM
      • cwmagee
        Reply to EX dust collection holes screwed up a project.!
        by cwmagee
        Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
        Today, 08:40 AM
      • Rolf
        Reply to EX dust collection holes screwed up a project.!
        by Rolf
        That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
        Today, 07:28 AM
      • handibunny
        Reply to EX dust collection holes screwed up a project.!
        by handibunny
        Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
        Today, 06:21 AM
      View All
      Working...
      X