Announcement

Collapse
No announcement yet.

Where is Bob??

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Where is Bob??

    Where is Bob? Stop by and say hello.
    John T.

  • #2
    I bet he is getting the next issue ready for print --or he is out chasing that darn fox out of the hen house ...
    Sharon

    Comment


    • #3
      I hope the next issue points out where the fox is, because I still haven't found it yet.

      Gill
      There is no opinion, however absurd, which men will not readily embrace as soon as they can be brought to the conviction that it is readily adopted.
      (Schopenhauer, Die Kunst Recht zu Behalten)

      Comment


      • #4
        Bob Who?
        There are a lot of Bobs in here.

        Bob
        Delta P-20 & Q-3

        I wondered why the baseball was getting bigger. Then it hit me!

        Comment


        • #5
          That would be BOB D. I bet he is looking for another good place to put the fox for the next issue. Either that he is just so busy scrolling away at his saw.
          John T.

          Comment


          • #6
            One word: Vacation!


            Sorry to get out of touch, but I was, and still am, very busy trying to get the next issue out! But I took a couple days to go to Colonial Williamsburg, VA. Got one of those discount vacations because they were trying to sell me a timeshare--and when I didn't buy, I think they poisoned my water <grin>. Either that, or the VA water didn't agree wiht me...Oh, well, Onward and upward!

            Bob
            www.GrobetUSA.com

            Comment


            • #7
              Thanks for checking in Bob because we were going to have to call off the fox chase and start the Bob chase. Don't drink the water. Didn't you learn that. Glad you are back at the desk and working hard. Boy that time share racket has been around for a long time now.
              John T.

              Comment

              Unconfigured Ad Widget

              Collapse

              Latest Topics

              Collapse

              • MidMich324
                Reply to hegner 2"
                by MidMich324
                Just Wondering...

                Is the table size on the 22" hegner saw as on the 18" hegner saw?

                With the 22" inch one you get 4 more inches of depth of cut but do you also get a few more inches of table?
                Today, 09:30 PM
              • will8989
                Reply to Spring Issue
                by will8989
                I had to fool around with copying and taping a pattern again today. This wasn’t as bad as the fish, but still a pain. I use rapid resizer. Scan a pattern, put in size I want and it prints it out. If more than one page, it numbers each page at the top and I tape them together. Had the fish pattern...
                Today, 09:28 PM
              • millwab
                Reply to Peanuts #1
                by millwab
                Rolf, I cover it with clear contact paper (comes off clean without leaving a residue) and draw a grid for the direction I want to cut (ie horizontal or diagonal) to keep the rows even. The rest is all freehand....
                Today, 02:51 PM
              • Don in Brooklin On
                Reply to Spring Issue
                by Don in Brooklin On
                Rolf

                I use acrobat reader. The poster feature will enlarge and if it goes to multiple pages it will put in cut marks. Even if the page is over letter size it will spread to multiple pages at 100%.

                If it is in PDF form you can open with Inkscape or GIMP and select what you...
                Today, 01:48 PM
              • theframer
                Reply to YoraHome Laser w/CNC Engraver/Router
                by theframer
                Hi Linda, great find...I think.

                Please keep us up to date with any information you receive. I would really like to get into this, but my computer skills are almost nonexistent, I need something that a 74 year old air head 🙄 can figure out. Thanks for sharing.

                Rick
                Today, 12:05 PM
              Working...
              X