Solution:
The trunion (inside the back end of the upper arm) is not intended to rotate. it binds the adjuster t-bolt to hold the upper arm in a raised position. The trunion must be fixed to the upper arm.
Fix:
I drilled into the joint between end of trunion and side of upper...
There are no conversations in this channel.
Please log in to your account to view your subscribed posts.
| Topics | Statistics | Last Post | |
|---|---|---|---|
|
44 responses
27,373 views
0 likes
|
by IntarsiaGuy
05-05-2016, 05:43 PM
|
||
|
Sticky:
Questions for Carole Rothman
|
87 responses
24,541 views
0 likes
|
by handibunny
09-18-2015, 12:18 PM
|
|
|
Sticky:
Questions for Kathy Wise
|
53 responses
24,758 views
0 likes
|
by unichjera
11-05-2011, 11:21 AM
|
|
|
Sticky:
Questions for Gary Browning
|
53 responses
24,542 views
0 likes
|
by WntrCrow
08-01-2011, 05:04 PM
|
|
|
4 responses
111 views
0 likes
|
by uncle dean
03-10-2019, 11:44 AM
|
||
|
11 responses
310 views
0 likes
|
by KarlB
01-12-2019, 05:49 PM
|
||
|
5 responses
143 views
0 likes
|
by domeclock6
09-20-2018, 12:30 PM
|
||
|
0 responses
104 views
2 likes
|
06-11-2018, 02:15 AM
|
||
|
10 responses
205 views
0 likes
|
by Hobbyhorse
05-04-2018, 09:49 PM
|
||
|
2 responses
101 views
2 likes
|
by BobD
02-22-2018, 09:28 AM
|
||
|
16 responses
327 views
0 likes
|
by DaveVanEss
08-05-2017, 10:34 AM
|
||
|
17 responses
442 views
0 likes
|
by stephenD
07-07-2017, 08:38 PM
|
||
|
4 responses
130 views
0 likes
|
by DaveVanEss
07-06-2017, 09:48 AM
|
||
|
24 responses
374 views
0 likes
|
by Rolf
06-28-2017, 07:41 AM
|
No topics found.
-
Reply to up stop for excalibur ex1903-10-2019, 11:44 AM
-
Reply to up stop for excalibur ex19Makes me happy just to hear of these old saws still in use. Parts are no longer available so there is not very many still running.03-04-2019, 10:04 AM -
Reply to up stop for excalibur ex1903-04-2019, 06:57 AM -
Reply to up stop for excalibur ex19I suspect it may have popped off while you werent looking. Have you scoured the floor for spare parts?03-03-2019, 03:03 PM -
I just finished replacing all the bearings in my Excalibur EX19VS and it runs smooth as glass,,, but,,,the upper arm will not stay up like it did before. I suspect something in the (rear) tension rod is not correct. My owners manual shows a coil spring below the Cross Trunnion, but my machine did not...03-03-2019, 11:24 AM
-
Well I thought there was. Maybe I am wrong in my comment. If so - my apologies.
Karl
Oh - wait! You're being funny aren't you? Got it!
Karl01-12-2019, 05:49 PM -
There was a semi blackout?...01-12-2019, 08:14 AM
-
Just sent out the index Clem.
Karl...01-11-2019, 08:00 PM -
Karl would be possible to get a copy of that CWW&C from you also jmcclements@xplornet.com...01-11-2019, 05:50 PM
-
Just sent the index out Bob.
Karl10-16-2018, 06:57 PM