Announcement

Collapse
No announcement yet.

New memeber posting?

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
  • #1

    New memeber posting?

    Hi, I just signed up and posted a thread yesterday in the General Scroll Saw, but I cant find my thread. Is there a time period one must wait before starting a new thread? Thanks
    Tags: None
  • #2
    I think the system refreshes itself, like every night or something... I've seen threads disappear too.. If no one responds to it in time, it will still be there but not out front...

    Anyway... WELCOME...!!!
    Great place here... I think you'll find that folks are very sharing around here..
    We'd love to see some pictures of your work..
    Jim

    The limits of the imagination are imaginary.
    No task is too tedious for Art.
    Rock and Scroll

    My Gallery

    My Website
    Featherwood Woodcrafts

    Comment

    • #3
      Hi Mudslag - your post is still listed - at least i can see it here
      http://www.scrollsawer.com/forum/gen...-saw/43483.htm

      Just one comment though. The images you have posted have been taken from another site which is not normally acceptable due to copyright issues. You should remove them and maybe just place a rough pencil sketch of the type of items you have in mind.
      Jim in Mexico

      Logic will get you from A to B. Imagination will take you everywhere.
      - Albert Einstein

      Comment

      Previous template Next

      Unconfigured Ad Widget

      Collapse

      Latest Topics

      Collapse
      • handibunny
        Reply to EX dust collection holes screwed up a project.!
        by handibunny
        Rolf, smaller bowl-cutting angles, 30˚ or less, usually don't present a problem either with vibration or for cutting into the table. It's when you get into the 40˚ and 45˚ range that things get dicey for both. (The Seyco saw doesn't even cut bevels greater than 35˚ or so!) If you add even a slight...
        Today, 09:21 AM
      • Bill Wilson
        Reply to EX dust collection holes screwed up a project.!
        by Bill Wilson
        I've done some bevel cutting on my EX-21 as well and also have not experienced any added vibration, nor have I cut into the table. Perhaps I haven't cut at a steep enough angle, but the existing blade hole has been sufficient. I do despise the useless vacuum holes, but I've learned to live with them...
        Today, 09:06 AM
      • cwmagee
        Reply to EX dust collection holes screwed up a project.!
        by cwmagee
        Carole Your hole size was a concern when I purchased the Pegas Replacement Table for my EX21, because I had cut into the side of hole on the original table, The damage I did to the old table was due to the blade adjustments were not in the center of blade holders. So far that has not been an issue...
        Today, 08:40 AM
      • Rolf
        Reply to EX dust collection holes screwed up a project.!
        by Rolf
        That is an interesting point Carole. I have done some bevel cutting on the EX and can't say that I have experienced an increase in vibration or any problems with following the lines. I know when I cut one of your bowl designs on my Hawk I really had to concentrate on not pushing down hill....
        Today, 07:28 AM
      • handibunny
        Reply to EX dust collection holes screwed up a project.!
        by handibunny
        Just a word of caution about the size of the blade hole. When I used a DeWalt years ago in the infamous community woodshop, and also with my more recent experiences with the Jet, if you do much bevel cutting at a steep angle, you will cut into the table. That's why inserts have the slot that can be...
        Today, 06:21 AM
      View All
      Working...
      X